The website uses cookies to provide personalized services at the highest level, including statistical services and to adapt the content to individual preferences of users. Saving cookies can be turned off in your browser settings.
OK
[zamknij]     

Loctite EA 3450 - 25 ml (epoxy resin, universal, two-compound)

Loctite EA 3450 - 25 ml (epoxy resin, universal, two-compound)

Cat. no.

IDH.1885773

Price

1-9 pcs
11,53 EUR netto
10-30 pcs
9,80 EUR netto
≥ 31 pcs
9,80 EUR netto
Loctite EA 3450 - 25 ml (epoxy resin, universal, two-compound) (IDH.1885773)
Product description:
LOCTITE EA 3450 is a two component epoxy adhesive which cures rapidly at room temperature after mixing. It is a metal bonding adhesive which develops high strength. The gap filling properties make this adhesive system suitable for rough and poorly fitting surfaces made from metal, ceramic, rigid plastics or wood. Applications include bonding aluminum window frames and GRP panels. Further information on the product can be obtained from your local technical department: biuro@woronko-loctite.pl

Steps to achieve the best adhesive results:
1. For best performance part surfaces should be clean and free of grease. Use LOCTITE 7063.
2. For high strength structural bonds, remove surface contaminants such as paint, oxide films, oils, dust, mold release agents and all other surface contaminants.
3. Dual Cartridges: To use simply insert the cartridge into the application gun and start the plunger into the cylinders using light pressure on the trigger. Next, remove the cartridge cap and expel a small amount of adhesive to be sure both sides are flowing evenly and freely. If automatic mixing of resin and hardener is desired, attach the mixing nozzle to the end of the cartridge and begin dispensing the adhesive. For hand mixing, expel the desired amount of the adhesive and mix thoroughly. Mix for approximately 15 seconds after uniform color is obtained. Bulk Containers: Mix thoroughly by weight or volume in the proportions specified in Product Description section. Mix vigorously, approximately 15 seconds after uniform color is obtained.
4. For maximum bond strength apply adhesive evenly to both surfaces to be joined.
5. Application to the substrates should be made within 20 minutes. Larger quantities and/or higher temperatures will reduce this working time.
6. Join the adhesive coated surfaces and allow to cure at 25 °C for 24 hours for high strength. Heat up to 93 °C, will speed curing.
7. Keep parts from moving during cure. Contact pressure is neccesary. Maximum shear strength is obtained with a 0,1 to 0,2 mm bond line.
8. Excess uncured adhesive can be wiped away with organic solvent (e.g. Acetone).
9. After use and before adhesive hardens mixing and dispensing equipment should be cleaned with hot soapy water.

Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.

Parameters:
PROPERTIES OF CURED MATERIAL:
Shear strength, ASTM D1002/DIN 53283 (szczelina 0,2 mm):
  • Steel (shot-blasted) (GB), N/mm² : 25
  • Steel (degreased), N/mm² : 19
  • Aluminum (shot-blasted), N/mm² : 15
  • Aluminum (degreased), N/mm² : 6
  • Wood, N/mm² : 5
  • Polycarbonate, N/mm² : 2
  • PCV, N/mm² : 1

Full technical information can be found in the technical data sheet.

Assortment