Try to find the solution
BONDERITE M-CR 1132 AERO (sztyft do aplikacji konwersyjnej powłoki chromianowanej klasy 1A MIL-DTL-5541, stosowana do me
No.
IDH.1446369
BONDERITE M-CR 1132 AERO (sztyft do aplikacji konwersyjnej powłoki chromianowanej klasy 1A MIL-DTL-5541, stosowana do me
Product description:
The Henkel BONDERITE M-CR 1132 AERO pen is designed to save labor, material, and time when applying a dry-inplace military specification approved chromate conversion coating for touch-up applications. Its proper use also reduces worker contact to chromatingsolutions and waste, such as rinse water generated from a chromating process.
Before starting the application procedure it is necessary to become familiar with the mechanics of the pen itself.
1. The pen is designed with a protective cap. The cap is simply popped off. DO NOT TWIST or turn to remove this cap.
2. To activate the pen hold the pen tip down on the surface to be treated. Press the pen down onto the surface. This opens the internal spring valve allowing the BONDERITE M-CR 1132 AERO to wet the applicator tip. The liquid’s yellow color will be visible. A new unit or new tip should charge in 15 to 30 seconds. When the BONDERITE M-CR 1132 AERO just wets the entire tip, release the downward pressure. The unit is ready to use.
3. Keep the pen’s tip wet with BONDERITE M-CR 1132 AERO , but do not overly saturate with the treatment solution.
4. Immediately after use, gently press the cap back onto the pen to protect the applicator from dirt and damage. Do not use excessive force when replacing the protective cap.
Directions for use:
Preliminary Statement:
Prior to use it is necessary to read the Material Safety Data Sheet for information about precautionary measures and safety recommendations. Also, for chemical products exempt from compulsory labeling, the relevant precautions should always be observed. Please also refer to the local safety instructions and contact Henkel for analytical support.
Cleaning:
Begin the process with a clean, water break free, dry surface. If the water rinse or treatment beads up on the surface, it has not been properly cleaned or it was re-contaminated. Avoid finger marks! Clean latex gloves are highly effective at preventing finger oil and lint contamination during cleaning. A preferred method of surface cleaning is the use of a wet Bear-Tex or Scotch Brite® Pad to abrade the surface. Abrasion of the surface in two directions at 90 degrees is recommended. After cleaning, rinse with water if appropriate and dry the surface with a clean cloth. If cleaning with a dry abrasive pad is required, a wipe with a clean damp cloth is recommended to help remove residues. Wipe until no dark residue is picked up from the surface. A surface clean of residue (smut, abrasive fines etc.) will help keep the felt tip from becoming fouled.
Coating Weights and Coverage:
This product is approved for Class 1A coatings in a wide range of coating weights. Heavy coating weights should be avoided for Class 3. MIL-DTL-81706A describes a strip-and-weigh coating weight determination method. The following table offers some guidance in obtaining the proper coating weight range and estimates expected coverage area per pen (with a second coat applied over the first dry coat).
Storage:
Temperature, °C : 0 to 40 Shelf-life (in unopened original packaging), months : 24
Full technical information about the product is in the technical data sheet.
The Henkel BONDERITE M-CR 1132 AERO pen is designed to save labor, material, and time when applying a dry-inplace military specification approved chromate conversion coating for touch-up applications. Its proper use also reduces worker contact to chromatingsolutions and waste, such as rinse water generated from a chromating process.
Before starting the application procedure it is necessary to become familiar with the mechanics of the pen itself.
1. The pen is designed with a protective cap. The cap is simply popped off. DO NOT TWIST or turn to remove this cap.
2. To activate the pen hold the pen tip down on the surface to be treated. Press the pen down onto the surface. This opens the internal spring valve allowing the BONDERITE M-CR 1132 AERO to wet the applicator tip. The liquid’s yellow color will be visible. A new unit or new tip should charge in 15 to 30 seconds. When the BONDERITE M-CR 1132 AERO just wets the entire tip, release the downward pressure. The unit is ready to use.
3. Keep the pen’s tip wet with BONDERITE M-CR 1132 AERO , but do not overly saturate with the treatment solution.
4. Immediately after use, gently press the cap back onto the pen to protect the applicator from dirt and damage. Do not use excessive force when replacing the protective cap.
Directions for use:
Preliminary Statement:
Prior to use it is necessary to read the Material Safety Data Sheet for information about precautionary measures and safety recommendations. Also, for chemical products exempt from compulsory labeling, the relevant precautions should always be observed. Please also refer to the local safety instructions and contact Henkel for analytical support.
Cleaning:
Begin the process with a clean, water break free, dry surface. If the water rinse or treatment beads up on the surface, it has not been properly cleaned or it was re-contaminated. Avoid finger marks! Clean latex gloves are highly effective at preventing finger oil and lint contamination during cleaning. A preferred method of surface cleaning is the use of a wet Bear-Tex or Scotch Brite® Pad to abrade the surface. Abrasion of the surface in two directions at 90 degrees is recommended. After cleaning, rinse with water if appropriate and dry the surface with a clean cloth. If cleaning with a dry abrasive pad is required, a wipe with a clean damp cloth is recommended to help remove residues. Wipe until no dark residue is picked up from the surface. A surface clean of residue (smut, abrasive fines etc.) will help keep the felt tip from becoming fouled.
Coating Weights and Coverage:
This product is approved for Class 1A coatings in a wide range of coating weights. Heavy coating weights should be avoided for Class 3. MIL-DTL-81706A describes a strip-and-weigh coating weight determination method. The following table offers some guidance in obtaining the proper coating weight range and estimates expected coverage area per pen (with a second coat applied over the first dry coat).
Storage:
Full technical information about the product is in the technical data sheet.
