Try to find the solution
BONDERITE C-AK 1574 - 1400kg (zasadowy zmywacz przemysłowy na bazie poliakrylanu i fosforanu do stali, ocynku i aluminiu
No.
IDH.864623
BONDERITE C-AK 1574 - 1400kg (zasadowy zmywacz przemysłowy na bazie poliakrylanu i fosforanu do stali, ocynku i aluminiu
Product description:
BONDERITE C-AK 1574 is a liquid alkaline cleaner based on phosphate for steel, zinc plated steel and aluminium.
Application Areas:
BONDERITE C-AK 1574 is used in spray- and spray/immersion processes. It must be combined with a suitable cleaning booster
Directions for use:
Preliminary Statement:
Prior to use it is necessary to read the Material Safety Data Sheet for information about precautionary measures and safety recommendations. Also, for chemical products exempt from compulsory labeling, the relevant precautions should always be observed. Please also refer to the local safety instructions and contact Henkel for analytical support.
Bath Make-up:
Depending on the substrate, make-up will be done with BONDERITE C-AK 1574 A or BONDERITE C-AK 1574. Fill the tank with warm water, start pumping and add for a volume of 1,000 L:
Zinc plated steel and aluminum:
BONDERITE C-AK 1574 A 7.4 to 22.3 L= 10 to 30 kg
Cleaning booster depends on requirements To avoid strong etching on sensitive surfaces, max. pH-value should be 11.2 (25°C). If higher, you have to add BONDERITE M-AD 100 to decrease pH-value.
Steel:
BONDERITE C-AK 1574 6.8 to 20.5 L = 10 to 30kg
Cleaning booster depends on requirements
Operating Data:
Adjusting the following parameters could be necessary depending on the line conditions.
Total alkalinity:
- BONDERITE C-AK 1574 A 3.8 to 11.4 mL
- BONDERITE C-AK 1574 7.0 to 20.9 mL
Free alkalinity:
- BONDERITE C-AK 1574 A 2.7 to 8.1 mL
- BONDERITE C-AK 1574 6.5 to 19.4 mL
- Temperature 50 to 80°C
- Duration of treatment 1 to 5 min
- Spray pressure 0.8 to 2.0 bar
Bath Control:
BONDERITE C-AK 1574 solution is controlled by the following analysis:
- Titration of total alkalinity:
- Feed, mL 10 mL
- Titrant: 0.1 N hydrochloric or 0.1N sulfuric acid
- End point: pH 3.6
- Indicator: bromecresolgreen (0.1 % alcoholic solution)
● Cool down bath solution to room temperature and pipette 10 mL bath solution into a clean 300 mL Erlenmeyer-flask.
● Add 50 mL deionized water.
● Add 4 to 5 drops of indicator.
● Titrate the solution with 0.1 N hydrochloric or 0.1 N sulfuric acid.
● The endpoint will be shown by a colour change from blue to yellow (pH: 3.6).
● The consumption of 0.1 N hydrochloric or 0.1 N sulfuric acid in mL is equal to the points of total alkalinity
Storage:
Recommended Storage Temperature, °C : -5 to 40 Shelf-life, months (in unopened original packaging) :18
Parameters:
Density : ~1.46 g/cm³ pH-value (1% in DI water 20°C): ~12.7
Full technical information about the product is in the technical data sheet.
BONDERITE C-AK 1574 is a liquid alkaline cleaner based on phosphate for steel, zinc plated steel and aluminium.
Application Areas:
BONDERITE C-AK 1574 is used in spray- and spray/immersion processes. It must be combined with a suitable cleaning booster
Directions for use:
Preliminary Statement:
Prior to use it is necessary to read the Material Safety Data Sheet for information about precautionary measures and safety recommendations. Also, for chemical products exempt from compulsory labeling, the relevant precautions should always be observed. Please also refer to the local safety instructions and contact Henkel for analytical support.
Bath Make-up:
Depending on the substrate, make-up will be done with BONDERITE C-AK 1574 A or BONDERITE C-AK 1574. Fill the tank with warm water, start pumping and add for a volume of 1,000 L:
BONDERITE C-AK 1574 A 7.4 to 22.3 L= 10 to 30 kg
Cleaning booster depends on requirements To avoid strong etching on sensitive surfaces, max. pH-value should be 11.2 (25°C). If higher, you have to add BONDERITE M-AD 100 to decrease pH-value.
BONDERITE C-AK 1574 6.8 to 20.5 L = 10 to 30kg
Cleaning booster depends on requirements
Operating Data:
Adjusting the following parameters could be necessary depending on the line conditions.
- BONDERITE C-AK 1574 A 3.8 to 11.4 mL
- BONDERITE C-AK 1574 7.0 to 20.9 mL
- BONDERITE C-AK 1574 A 2.7 to 8.1 mL
- BONDERITE C-AK 1574 6.5 to 19.4 mL
- Temperature 50 to 80°C
- Duration of treatment 1 to 5 min
- Spray pressure 0.8 to 2.0 bar
Bath Control:
- Titration of total alkalinity:
- Feed, mL 10 mL
- Titrant: 0.1 N hydrochloric or 0.1N sulfuric acid
- End point: pH 3.6
- Indicator: bromecresolgreen (0.1 % alcoholic solution)
● Cool down bath solution to room temperature and pipette 10 mL bath solution into a clean 300 mL Erlenmeyer-flask.
● Add 50 mL deionized water.
● Add 4 to 5 drops of indicator.
● Titrate the solution with 0.1 N hydrochloric or 0.1 N sulfuric acid.
● The endpoint will be shown by a colour change from blue to yellow (pH: 3.6).
● The consumption of 0.1 N hydrochloric or 0.1 N sulfuric acid in mL is equal to the points of total alkalinity
Storage:
Parameters:
Full technical information about the product is in the technical data sheet.
