POLYPOXY PS - 20l (corrosion protection and protection coating againts chemicals)
No.
IDH.2243014
Files to download:
POLYPOXY PS - 20l (corrosion protection and protection coating againts chemicals)
Product description:
POLYPOXY PS is a polysulphide modified epoxy resin protective coating designed for superior adhesion, corrosion protection and high chemical resistance for concrete and steel structures. It is a two part system which can be applied up to 1mm thickness to provide a flexible, elastomeric, crack bridging, water and chemical resistant coating.
CHARACTERISTICS:
Enhanced adhesion to many substrates including rusted and damp surfaces Good corrosion protection Good impact resistance Chemical resistance to a wide variety of fluids in particular to those used in the automotive and aerospace industries Thermal shock resistance. Good electrical properties and controlled acoustic dampning characteristics Very low permeability to water and vapor Non-Toxic Good UV resistance Good Flexibility and crack bridging ability Easy to apply
FIELDS OF APPLICATION:
Industrial corrosion protection of steel and concrete structures Hard wearing floor coating in industrial areas Water proofing of potable water structure Protective coating to exposed concrete structures Waterproofing & Protection of swimming pools, water tanks etc Corrosion protection of steel and concrete in sweet and salt water atmosphere as well as protection against chemical and carbonation attacks Internal lining of manholes & treaded sewage holding tanks
SPECIALTY:
POLYPOXY PS has the quality & chemical resistance of Epoxy plus the flexibility and adhesion properties of Polysulphide resins.
APPLICATION INSTRUCTIONS:
Surface preparation
The surface should be free from dust, dirt, curing compound, oil etc. Clean the surface thoroughly to remove all loosely adhering particles and cement laitance. It is recommended to use a light mechanical grinder for cleaning. Cracks and pot holes should be repaired with a suitable product from the POLYCRETE range.
Priming
Prime the prepared surface with POLYPRIME EP (Epoxy resin based primer) and allow to dry. For damp, corroded & contaminated surfaces POLYPRIME R is recommended to be used. Priming is not required for steel surfaces.
Mixing
Mix Part A (resin) and Part B (hardener) separately for a minute using a slow speed drill fitted with a paddle to remove any sediment. Then add Part B into the Part A pail and mix thoroughly for 2– 3 minutes to achieve a uniform consistency. Apply immediately after mixing within its pot life.
Application
Apply the coating with a brush, roller or airless spray (nozzle size 0.4-0.6 mm @2500 psi pressure). On vertical surfaces apply the coating at a wet film thickness of 250 microns in a single coat. Since the coating is heavy bodied, dripping may be observed if it is applied at a higher thickness. Additional coats can be applied only when the previous coat dries off completely (8-10 hours. After application the coating must be back rolled to reduce surface irregularities and to improve bonding. Care should be taken to ensure that a continuous film is achieved. NOTE: The coating can be applied as a flexible and crack free flooring with an anti slip finish. Graded sand/quartz can be broadcasted on the first coat while it is still wet and allowed to dry completely. After a period of 24 hours, the excess sand/quartz can be brushed away and the second coat is to be given.
CLEANING:
Clean all equipments with a POLYSOLVENT. Hardened materials can be removed mechanically only.
STORAGE & SHELF LIFE:
Store under cover, out of direct sunlight and protect from extreme temperatures. In tropical climates the produce must be stored in air–conditioned environment. Shelf life is up to 12 months when stored as per recommendations. Excessive exposure to heatand high humidity will result in the deterioration of the product and reduce its shelf life considerably
TECHNICAL SPECIFICATION:
PROPERTIES VALUES Chemical Type : Polysulphide Modified Epoxy Resin Mixed Density, [g/cc] 1.6±0.05 Color : Grey (Other colors upon request) Application life [mins] : 60 Re-coating [hrs] : 10-12 Chemical Resistance : Dilute acids and alkalis, solvents, oil, petrol, effluents, sea water etc. Application temp, [°C] : 5 to 35 Service temp, [°C] : 5 to 70
POLYPOXY PS is a polysulphide modified epoxy resin protective coating designed for superior adhesion, corrosion protection and high chemical resistance for concrete and steel structures. It is a two part system which can be applied up to 1mm thickness to provide a flexible, elastomeric, crack bridging, water and chemical resistant coating.
CHARACTERISTICS:
FIELDS OF APPLICATION:
SPECIALTY:
POLYPOXY PS has the quality & chemical resistance of Epoxy plus the flexibility and adhesion properties of Polysulphide resins.
APPLICATION INSTRUCTIONS:
Surface preparation
The surface should be free from dust, dirt, curing compound, oil etc. Clean the surface thoroughly to remove all loosely adhering particles and cement laitance. It is recommended to use a light mechanical grinder for cleaning. Cracks and pot holes should be repaired with a suitable product from the POLYCRETE range.
Priming
Prime the prepared surface with POLYPRIME EP (Epoxy resin based primer) and allow to dry. For damp, corroded & contaminated surfaces POLYPRIME R is recommended to be used. Priming is not required for steel surfaces.
Mixing
Mix Part A (resin) and Part B (hardener) separately for a minute using a slow speed drill fitted with a paddle to remove any sediment. Then add Part B into the Part A pail and mix thoroughly for 2– 3 minutes to achieve a uniform consistency. Apply immediately after mixing within its pot life.
Application
Apply the coating with a brush, roller or airless spray (nozzle size 0.4-0.6 mm @2500 psi pressure). On vertical surfaces apply the coating at a wet film thickness of 250 microns in a single coat. Since the coating is heavy bodied, dripping may be observed if it is applied at a higher thickness. Additional coats can be applied only when the previous coat dries off completely (8-10 hours. After application the coating must be back rolled to reduce surface irregularities and to improve bonding. Care should be taken to ensure that a continuous film is achieved. NOTE: The coating can be applied as a flexible and crack free flooring with an anti slip finish. Graded sand/quartz can be broadcasted on the first coat while it is still wet and allowed to dry completely. After a period of 24 hours, the excess sand/quartz can be brushed away and the second coat is to be given.
CLEANING:
Clean all equipments with a POLYSOLVENT. Hardened materials can be removed mechanically only.
STORAGE & SHELF LIFE:
Store under cover, out of direct sunlight and protect from extreme temperatures. In tropical climates the produce must be stored in air–conditioned environment. Shelf life is up to 12 months when stored as per recommendations. Excessive exposure to heatand high humidity will result in the deterioration of the product and reduce its shelf life considerably
TECHNICAL SPECIFICATION:
PROPERTIES VALUES
