Try to find the solution
LOCTITE EA 3471 - 500g (epoxy resin with metal filler)
No.
IDH.229176
Price
LOCTITE EA 3471 - 500g (epoxy resin with metal filler)
Product description:
LOCTITE EA 3471 is a steel reinforced, two-part epoxy repair putty that cures to a metal-like finish and can be machined, drilled, tapped or filed. Typical applications include repairing non-structural defects in castings, making jigs and fixtures, sealing vessels, tanks and valves, resurfacing worn air seals and filling cavitated areas. This product is typically used in applications with an operating range of -30 °C to 105 °C. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
Application
1. Mix resin and hardener according to mix ratios listed or transfer entire kit onto a clean and dry mixing surface and mix material vigorously until a uniform color is obtained.
2. Apply material to prepared surface by first forcing a thin layer deep into the texture of the substrate.
3. Then Immediately build up to the desired finished thickness.
4. If using to rebuild shaft, the following applies:
● Machine the worn area down 3 mm (0.125 in) to produce a square shoulder on part. The material is stronger with a square edge versus a feathered edge.
● Machine a spiral cut in bottom of area to be repaired to provide mechanical keying into surface.
● Apply excess product to ensure small shrinkage during cure does not produce depression.
● Machine the surface to original dimensions prior to full cure, as the product is very wear resistant.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
LOCTITE EA 3471 is a steel reinforced, two-part epoxy repair putty that cures to a metal-like finish and can be machined, drilled, tapped or filed. Typical applications include repairing non-structural defects in castings, making jigs and fixtures, sealing vessels, tanks and valves, resurfacing worn air seals and filling cavitated areas. This product is typically used in applications with an operating range of -30 °C to 105 °C. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
Application
1. Mix resin and hardener according to mix ratios listed or transfer entire kit onto a clean and dry mixing surface and mix material vigorously until a uniform color is obtained.
2. Apply material to prepared surface by first forcing a thin layer deep into the texture of the substrate.
3. Then Immediately build up to the desired finished thickness.
4. If using to rebuild shaft, the following applies:
● Machine the worn area down 3 mm (0.125 in) to produce a square shoulder on part. The material is stronger with a square edge versus a feathered edge.
● Machine a spiral cut in bottom of area to be repaired to provide mechanical keying into surface.
● Apply excess product to ensure small shrinkage during cure does not produce depression.
● Machine the surface to original dimensions prior to full cure, as the product is very wear resistant.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
- Properties of cured material:
- Hardness (Shora D) : 82
- Compressive strength : 61,7 N/mm²
- Tensile strength : 27,8 N/mm²
- Tensile modulus : 9,36 N/mm²
- Working temperature: from -30 °C to +105 °C
- Color : grey paste
- Shear stremgth after 7 days (temperature 23 °C).
- Shot-blasted steel : 9,6 N/mm²
Full technical information can be found in the technical data sheet
