Try to find the solution
LOCTITE EA 3430 - 50ml (epoxy adhesive)
No.
IDH.2035020
Price
Associated products:
- LOCTITE 96001 (manual applicator for 50ml cartridges, mixing ratio of components A&B 1:1 or 1:2) (IDH.267452)
- LOCTITE 97956 (adapter for double (1:1) 50ml cartridges, compatible with standard 300ml cartridge squeezers) (IDH.476895A)
- LOCTITE EA 3430 - 24ml (epoxy adhesive) (IDH.242865)
- TEROSON ET QUAD ST MIX SMALL (for 50 ml cartridges 1:1, 1:2) (IDH.2900614)
- LOCTITE Double-Bubble - 3g (epoxy adhesive) (IDH.2015058)
- LOCTITE SF 7063 - 400ml (degreasing agent for plastics and metals) spray (IDH.2385316)
LOCTITE EA 3430 - 50ml (epoxy adhesive)
Associated products:
- LOCTITE 96001 (manual applicator for 50ml cartridges, mixing ratio of components A&B 1:1 or 1:2) (IDH.267452)
- LOCTITE 97956 (adapter for double (1:1) 50ml cartridges, compatible with standard 300ml cartridge squeezers) (IDH.476895A)
- LOCTITE EA 3430 - 24ml (epoxy adhesive) (IDH.242865)
- TEROSON ET QUAD ST MIX SMALL (for 50 ml cartridges 1:1, 1:2) (IDH.2900614)
- LOCTITE Double-Bubble - 3g (epoxy adhesive) (IDH.2015058)
- LOCTITE SF 7063 - 400ml (degreasing agent for plastics and metals) spray (IDH.2385316)
Product description:
LOCTITE® EA 3430 is a two component, clear epoxy adhesive which cures rapidly at room temperature after mixing. It is a general purpose adhesive which develops high strength on a wide range of substrates. The gap filling properties make this adhesive system suitable for rough and poorly fitting surfaces made from metal, ceramic, rigid plastics or wood. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. For best performance surfaces for bonding should be clean, dry and free of grease. You can use LOCTITE SF 7063. For high strength structural bonds, special surface treatments can increase the bond strength and durability.
2. To use, resin and hardener must be blended. Product can be applied directly from dual cartridges by dispensing through the mixer head supplied. Discard the first 3 to 8 cm of bead dispensed. Using twin cartridges or bulk containers, mix thoroughly by weight or volume in the proportions specified in the Product Description Matrix. For hand mixing, weigh or measure out the desired amount of resin and hardener and mix thoroughly. Mix approximately 15 seconds after uniform color is obtained.
3. Do not mix quantities greater than 20 g in mass as excessive heat build-up can occur. Mixing smaller quantities will minimize the heat build-up.
4. Apply the adhesive as quickly as possible after mixing to one surface to be joined. For maximum bond strength apply adhesive evenly to both surfaces. Parts should be assembled immediately after mixed adhesive has been applied.
5. Working life of the mixed adhesive is ≤4 minutes ( 22 °C ). Higher temperature and larger quantities will shorten this working time.
6. Keep the assembled parts from moving during cure. The joint should be allowed to develop full strength before subjecting to any service loads.
7. Excess uncured adhesive can be wiped away with organic solvent (e.g. Acetone).
8. After use and before adhesive hardens, mixing and application equipment should be cleaned with hot soapy water.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Shear strength, ASTM D1002/DIN 53283 (at the gap 0,3 mm) :
Full technical information can be found in the technical data sheet.
LOCTITE® EA 3430 is a two component, clear epoxy adhesive which cures rapidly at room temperature after mixing. It is a general purpose adhesive which develops high strength on a wide range of substrates. The gap filling properties make this adhesive system suitable for rough and poorly fitting surfaces made from metal, ceramic, rigid plastics or wood. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. For best performance surfaces for bonding should be clean, dry and free of grease. You can use LOCTITE SF 7063. For high strength structural bonds, special surface treatments can increase the bond strength and durability.
2. To use, resin and hardener must be blended. Product can be applied directly from dual cartridges by dispensing through the mixer head supplied. Discard the first 3 to 8 cm of bead dispensed. Using twin cartridges or bulk containers, mix thoroughly by weight or volume in the proportions specified in the Product Description Matrix. For hand mixing, weigh or measure out the desired amount of resin and hardener and mix thoroughly. Mix approximately 15 seconds after uniform color is obtained.
3. Do not mix quantities greater than 20 g in mass as excessive heat build-up can occur. Mixing smaller quantities will minimize the heat build-up.
4. Apply the adhesive as quickly as possible after mixing to one surface to be joined. For maximum bond strength apply adhesive evenly to both surfaces. Parts should be assembled immediately after mixed adhesive has been applied.
5. Working life of the mixed adhesive is ≤4 minutes ( 22 °C ). Higher temperature and larger quantities will shorten this working time.
6. Keep the assembled parts from moving during cure. The joint should be allowed to develop full strength before subjecting to any service loads.
7. Excess uncured adhesive can be wiped away with organic solvent (e.g. Acetone).
8. After use and before adhesive hardens, mixing and application equipment should be cleaned with hot soapy water.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Shear strength, ASTM D1002/DIN 53283 (at the gap 0,3 mm) :
- Steel (shot-blasted) : 20 N/mm²
- Shot blasted galvanized steel: 10 N/mm²
- Aluminum (shot-blasted) : 14 N/mm²
- Copper (shot-blasted) : 19 N/mm²
- Brass (shot-blasted) : 15 N/mm²
- Polycarbonate : 5 N/mm²
- SMC : 7 N/mm²
- ABS : 3 N/mm²
Full technical information can be found in the technical data sheet.
