TEROSON Bond All In One - 100ml (Primer for window adhesive)
No.
IDH.2670909
Files to download:
TEROSON Bond All In One - 100ml (Primer for window adhesive)
Product description:
TEROSON® BOND ALL-IN-ONE PRIMER is a thin liquid, solvent containing masking aid based on polyurethane. The product is notable for its excellent covering properties and its good UV-stability. The primer is suitable for promoting the adhesion of other PUR adhesives/sealants to glass, glass ceramic, various plastics, metals and can also be used for PUR-coated glasses and remaining beads. TEROSON® BOND ALL-IN-ONE PRIMER is also suitable as corrosion protection for small flange damages. It is free from chlorinated hydrocarbons and aromatic solvents. Typical applications include the bonding of front, rear and side screens to the body of passenger-, utility-, special- and rail vehicles. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
Preparation
Prior to use, shake the aluminum bottle vigorously by hand for at least 1 minute. A steel ball is provided in the bottle to assist mixing. This should move freely after three to four shakes.
Application
TEROSON® BOND ALL-IN-ONE PRIMER may be applied thinly and evenly with felt applicator or TEROSON® BOND SPONGE. Let the primed surface evaporate as stated before the direct glazing adhesive is applied. A second application on the same point should be avoided, as partially dried primer will be softened again which can adversely affect adhesion properties. The optimal application temperature is between 5 to 30°C. In exceptional cases the application can be done at higher temperatures. A higher reaction speed will be noticed.
Storage:
Store product in the unopened container in a dry location. Storage information may also be indicated on the product container labelling. Optimal Storage: 15 to 25 °C. Storage below 5 °C or greater than 25 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameter:Chemical type : polyurethane Appearance (uncured) : black liquid Components : one-component – requires no mixing Viscosity : liquid Cure : humidity Application : surface pretreatment Environmental temperature at application : -5 to 45 °C Material application temperature : 5 to 35 °C In service temperature : -40 to 90 °C Short exposure (up to 1h) : 120°C Specific Gravity : 0.98 Solids, % : 35 Drying time, minutes (1C adhesive) : 2 Drying time, minutes (2C adhesive) : 15 Open time, hours : 8
Full technical information can be found in the technical data sheet
TEROSON® BOND ALL-IN-ONE PRIMER is a thin liquid, solvent containing masking aid based on polyurethane. The product is notable for its excellent covering properties and its good UV-stability. The primer is suitable for promoting the adhesion of other PUR adhesives/sealants to glass, glass ceramic, various plastics, metals and can also be used for PUR-coated glasses and remaining beads. TEROSON® BOND ALL-IN-ONE PRIMER is also suitable as corrosion protection for small flange damages. It is free from chlorinated hydrocarbons and aromatic solvents. Typical applications include the bonding of front, rear and side screens to the body of passenger-, utility-, special- and rail vehicles. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
Preparation
Prior to use, shake the aluminum bottle vigorously by hand for at least 1 minute. A steel ball is provided in the bottle to assist mixing. This should move freely after three to four shakes.
Application
TEROSON® BOND ALL-IN-ONE PRIMER may be applied thinly and evenly with felt applicator or TEROSON® BOND SPONGE. Let the primed surface evaporate as stated before the direct glazing adhesive is applied. A second application on the same point should be avoided, as partially dried primer will be softened again which can adversely affect adhesion properties. The optimal application temperature is between 5 to 30°C. In exceptional cases the application can be done at higher temperatures. A higher reaction speed will be noticed.
Storage:
Store product in the unopened container in a dry location. Storage information may also be indicated on the product container labelling. Optimal Storage: 15 to 25 °C. Storage below 5 °C or greater than 25 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameter:
Full technical information can be found in the technical data sheet
