LOCTITE AA 128500/3504 - 250 ml (UV-cured acrylic adhesive)
No.
IDH.195539
LOCTITE AA 128500/3504 - 250 ml (UV-cured acrylic adhesive)
Product description:
LOCTITE AA 3504 typical applications include bonding ferrites to plated materials in electric motors, loudspeaker hardware and jewelry where fast fixturing is required and where product outside the bondline must be completely cured. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. LOCTITE AA 3504 is UV sensitive. Exposure to daylight, UV light and artificial lighting should be kept to a minimum during storage and handling.
2. The product should be dispensed from applicators with black feedlines.
3. For best performance bond surfaces should be clean and free from grease. Use LOCTITE SF 7063.
4. Cure rate is dependent on lamp intensity, distance from light source, depth of cure needed or bondline gap and light transmittance of the substrate through which the radiation must pass.
5. Cooling should be provided for temperature sensitive substrates such as thermoplastics.
6. Crystalline and semi-crystalline thermoplastics should be checked for risk of stress cracking when exposed to liquid adhesive.
7. Excess adhesive can be wiped away with organic solvent.
8. Bonds should be allowed to cool before subjecting to any service loads.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Chemical type: methacrylate Appearance: clear, amber Specific gravity in 25°C : 1,10 Viscosity in 25°C, mPa.s (cP), Brookfield RVT ( at 20 rpm) : 1,000 Coefficient of thermal conductivity, ISO 8302, W/(m·K) : 0.1 Hardness Shore'a, ISO 868, Durometr D: 45
Tensile strength, ISO 6922 ( cured 20 seconds ):
Full technical information can be found in the technical data sheet.
LOCTITE AA 3504 typical applications include bonding ferrites to plated materials in electric motors, loudspeaker hardware and jewelry where fast fixturing is required and where product outside the bondline must be completely cured. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. LOCTITE AA 3504 is UV sensitive. Exposure to daylight, UV light and artificial lighting should be kept to a minimum during storage and handling.
2. The product should be dispensed from applicators with black feedlines.
3. For best performance bond surfaces should be clean and free from grease. Use LOCTITE SF 7063.
4. Cure rate is dependent on lamp intensity, distance from light source, depth of cure needed or bondline gap and light transmittance of the substrate through which the radiation must pass.
5. Cooling should be provided for temperature sensitive substrates such as thermoplastics.
6. Crystalline and semi-crystalline thermoplastics should be checked for risk of stress cracking when exposed to liquid adhesive.
7. Excess adhesive can be wiped away with organic solvent.
8. Bonds should be allowed to cool before subjecting to any service loads.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Tensile strength, ISO 6922 ( cured 20 seconds ):
- Steel peg for glass, N/mm² : 10
- Steel (shot-blasted), N/mm² : ≥22
Full technical information can be found in the technical data sheet.
