LOCTITE SI 5710 - 400ml (Silicone adhesive)
No.
IDH.2571794
Files to download:
Product description:
LOCTITE® SI 5710™ is an ultra clear, two-part silicone which cures at room temperature and can be accelerated by heat.Thanks to polyaddition technology, the product releases no by-products, has low shrinkage, is non-corrosive and healthand safety friendly. LOCTITE® SI 5710™ provides high transparency with a high transmission rate and is used for potting applications in the Lighting, Electrical and Optical industries for LED channel or lenses, optical sensors or coating processes. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. For best performance the mating surface should be clean and free of grease. You can use LOCTITE SF 7063.
2. Special surface treatments can increase the bond strength and durability.
3. Best results are achieved utilizing a helix 8mm diameter, 24 element mix nozzle.
4. Dual Cartridges: Insert the cartridge into the application gun and start the plunger into the cylinders using light pressure on the trigger. Next, remove the cartridge cap and expel a small amount of adhesive to be sure both sides are flowing evenly and freely. Attach the static mixing nozzle to the end of the cartridge and begin dispensing the adhesive. Purge and dispose of the first 3- 5 cm from the end of the mix nozzle, as it may not be sufficiently mixed. Bulk Containers: Utilize volumetric dispense system to ensure proper mix ratio and utilize mix nozzle to obtain adequate mixing.
5. Excess uncured adhesive can be wiped away with organic solvent (e.g. Acetone).
6. Certain materials can inhibit the curing of LOCTITE® SI 5710™, such as organotin compounds, sulfur-containing materials and amine-containing materials.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:Shore Hardness, ISO 868, Durometer A : 31 Water Absorption, % : 0.48 Coefficient of Thermal Expansion,, K-1 : 380×10-6 Elongation, at break, ISO 527-3, %: 130 Tensile Strength, ISO 527-3 N/mm² : 2.3 Tensile Modulus, ISO 37 N/mm² : 0.8 Density, g/cm³ : 1.0
Full technical information can be found in the technical data sheet
LOCTITE® SI 5710™ is an ultra clear, two-part silicone which cures at room temperature and can be accelerated by heat.Thanks to polyaddition technology, the product releases no by-products, has low shrinkage, is non-corrosive and healthand safety friendly. LOCTITE® SI 5710™ provides high transparency with a high transmission rate and is used for potting applications in the Lighting, Electrical and Optical industries for LED channel or lenses, optical sensors or coating processes. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. For best performance the mating surface should be clean and free of grease. You can use LOCTITE SF 7063.
2. Special surface treatments can increase the bond strength and durability.
3. Best results are achieved utilizing a helix 8mm diameter, 24 element mix nozzle.
4. Dual Cartridges: Insert the cartridge into the application gun and start the plunger into the cylinders using light pressure on the trigger. Next, remove the cartridge cap and expel a small amount of adhesive to be sure both sides are flowing evenly and freely. Attach the static mixing nozzle to the end of the cartridge and begin dispensing the adhesive. Purge and dispose of the first 3- 5 cm from the end of the mix nozzle, as it may not be sufficiently mixed. Bulk Containers: Utilize volumetric dispense system to ensure proper mix ratio and utilize mix nozzle to obtain adequate mixing.
5. Excess uncured adhesive can be wiped away with organic solvent (e.g. Acetone).
6. Certain materials can inhibit the curing of LOCTITE® SI 5710™, such as organotin compounds, sulfur-containing materials and amine-containing materials.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Full technical information can be found in the technical data sheet