LOCTITE EA 9450 - 400ml (translucent epoxy adhesive, up to 100 °C)
No.
IDH.2036815
Associated products:
- Mixing nozzle Stat Mixer 7.5-24 1:1 and 2:1, Type No. 984570 (200/400ml cat.) (IDH.1487439A)
- LOCTITE SF 7063 - 400ml (degreasing agent for plastics and metals) spray (IDH.2385316)
- LOCTITE EQ HD 14 400ml 2K (pneumatic dispenser for 2K cartridges) (IDH.2693825)
- LOCTITE EA 9450 - 50ml (translucent epoxy adhesive, up to 100 °C) (IDH.2036535)
- LOCTITE Universal Fixmaster Dispenser 200ml, 400ml, 490ml, manual gun (IDH.1372751)
- LOCTITE EQ HD 14 400ml 2K (manual dispenser for 2K cartridges) (IDH.2693823)
LOCTITE EA 9450 - 400ml (translucent epoxy adhesive, up to 100 °C)
Associated products:
- Mixing nozzle Stat Mixer 7.5-24 1:1 and 2:1, Type No. 984570 (200/400ml cat.) (IDH.1487439A)
- LOCTITE SF 7063 - 400ml (degreasing agent for plastics and metals) spray (IDH.2385316)
- LOCTITE EQ HD 14 400ml 2K (pneumatic dispenser for 2K cartridges) (IDH.2693825)
- LOCTITE EA 9450 - 50ml (translucent epoxy adhesive, up to 100 °C) (IDH.2036535)
- LOCTITE Universal Fixmaster Dispenser 200ml, 400ml, 490ml, manual gun (IDH.1372751)
- LOCTITE EQ HD 14 400ml 2K (manual dispenser for 2K cartridges) (IDH.2693823)
Product description:
LOCTITE EA 9450 is a fast curing two component epoxy adhesive suitable for a wide variety of substrates like metals, ceramics, glass and most plastics. LOCTITE EA 9450 is designed for use in component assembly, domestic appliances, electronics and fiber optics, and general industrial repairs. Its non-sagging formula is especially suited for use on vertical surfaces to avoid run-off. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. For best performance surfaces for bonding should be clean, dry and free of grease. You can use LOCTITE SF 7063. For high strength structural bonds, special surface treatments can increase the bond strength and durability.
2. To use, resin and hardener must be blended. Product can be applied directly from dual cartridges by dispensing through the mixer head supplied. Discard the first 3 to 5 cm of bead dispensed. Using bulk containers, mix thoroughly by weight or volume in the proportions specified in the Product Description Matrix. For hand mixing, weigh or measure out the desired amount of resin and hardener and mix thoroughly. Mix approximately 15 seconds after uniform color is obtained.
3. It is recommended that this product is not mixed and cured in bulk quantities of greater than 20 g as excessiveheat build-up can occur. Mixing smaller quantities will minimize the heat build-up.
4. Apply the adhesive as quickly as possible after mixing to one surface to be joined. For maximum bond strengthapply adhesive evenly to both surfaces. Parts should be assembled immediately after mixed adhesive has been applied.
5. For working life please see section 'Typical Properties of Uncured Material'. Higher temperatures and largerquantities will shorten this working time.
6. Keep the assembled parts from moving during cure. The joint should be allowed to develop full strength before subjecting to any service loads.
7. Excess uncured adhesive can be wiped away with organic solvent (e.g. Acetone).
8. After use and before adhesive hardens, mixing and application equipment should be cleaned with hot soapy water.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Full technical information can be found in the technical data sheet.
LOCTITE EA 9450 is a fast curing two component epoxy adhesive suitable for a wide variety of substrates like metals, ceramics, glass and most plastics. LOCTITE EA 9450 is designed for use in component assembly, domestic appliances, electronics and fiber optics, and general industrial repairs. Its non-sagging formula is especially suited for use on vertical surfaces to avoid run-off. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. For best performance surfaces for bonding should be clean, dry and free of grease. You can use LOCTITE SF 7063. For high strength structural bonds, special surface treatments can increase the bond strength and durability.
2. To use, resin and hardener must be blended. Product can be applied directly from dual cartridges by dispensing through the mixer head supplied. Discard the first 3 to 5 cm of bead dispensed. Using bulk containers, mix thoroughly by weight or volume in the proportions specified in the Product Description Matrix. For hand mixing, weigh or measure out the desired amount of resin and hardener and mix thoroughly. Mix approximately 15 seconds after uniform color is obtained.
3. It is recommended that this product is not mixed and cured in bulk quantities of greater than 20 g as excessiveheat build-up can occur. Mixing smaller quantities will minimize the heat build-up.
4. Apply the adhesive as quickly as possible after mixing to one surface to be joined. For maximum bond strengthapply adhesive evenly to both surfaces. Parts should be assembled immediately after mixed adhesive has been applied.
5. For working life please see section 'Typical Properties of Uncured Material'. Higher temperatures and largerquantities will shorten this working time.
6. Keep the assembled parts from moving during cure. The joint should be allowed to develop full strength before subjecting to any service loads.
7. Excess uncured adhesive can be wiped away with organic solvent (e.g. Acetone).
8. After use and before adhesive hardens, mixing and application equipment should be cleaned with hot soapy water.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
- Appearance (Resin) : translucent white paste
- Appearance (Hardener) : translucent light yellow paste
- Appearance (Mixture) : translucent paste
- Components : two part - resin & hardener
- Lap Shear Strength, ISO 4587 ( Cured for 5 days at 22 °C ):
-Mild steel (grit blasted), N/mm² : 23
-Stainless steel, N/mm² 14
-Aluminum (abraded), N/mm² : 9
-Aluminum (anodised), N/mm² : 8
-Polycarbonate, N/mm² : 2,5
-Nylon, N/mm² : 1
-Wood (Fir), N/mm² : 10
Full technical information can be found in the technical data sheet.