TEROSON RB R2000 HS GY - 1l (corrosion protection) / Terotex Record 2000 HS
No.
IDH.2671601
Product description:
TEROSON RB R2000 HS is a solvent containing coating material, free of bitumen, based on rubber/resins. After complete drying, the coating exhibits a permanently elastic corrosion protection with good aging characteristics and no cracking at low temperatures, due to its combination of raw materials. The dry film adheres well to cleaned underbodies, also to painted surfaces and exhibits a very high abrasionresistance. Painting with standard automotive paints (conventional and water based) is possible under the following conditions:
- allow minimum 16 hours drying of the coating
- apply a fine paint mist prior to final painting
- final painting only after beginning of drying of the pre-paintingsubsequent oven drying at 60°C possible.
Application areas:
TEROSON RB R2000 HS is suitable for repair work on the underbody, wheel house, front and rear aprons, spoilers, door sills, particularly as protection against road stones. The material is used as coating for painted parts or primer surfaced metals on the underbody and for repair works on coatings which are based on rubber/resins. TEROSON RB R2000 HS is also suitable for sound damping of wheel houses and side walls, and for covering and sealing of repair jobs, welding seams and overlaps. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
Pretreatment
Surfaces to be treated with TEROSON RB R2000 HS have to be cleaned well and rust must be removed. The areas must be dry and free of grease, dirt and to a great extent free of dust. Areas not to be coated should be covered with masking paper. In the case of new vehicles, protective wax must be steam-cleaned. If applied to older vehicles, watch out for beginning of rust formation, which has to be removed with a wire brush.
Application
TEROSON RB R2000 HS is applied with the Teroson UBC-Gun from 1-l-cans; application pressure: 4 - 5 bar. Shake the can well up side down for 1 minute before use. Opened containers must not be left open because the material will form a skin. On vertical surfaces, the underbody coating can be applied in one step up to 1 mm layer thickness (wet film). In order to avoid bare patches, the material should be sprayed in criss-cross fashion. Under favourable weather conditions, the vehicle is ready for use 2 - 4 hours afterapplication. For final drying 24 - 48 hours are necessary.
Storage:Frost sensitive : no Recommended storage temperature : 10 to 25 °C Shelf life : 18 months in original packaging
Parameters:
Colour : black , grey, white Odour : of petroleum spirit Consistency : thick liquid Density : approx. 1.22 g/cm³ Solids : approx. 64 % Sag resitance : good Layer thickness : wet 1 mm Skin formation time : 2 to 4 hrs Curing through : 24 to 48 hrs Abrasion resistance : very high Application temperature : 10 to 25 °C In service temperature : -25 to 80 °C Short exposure (up to 1h) : 100 °C
Full technical information can be found in technical data sheet
TEROSON RB R2000 HS is a solvent containing coating material, free of bitumen, based on rubber/resins. After complete drying, the coating exhibits a permanently elastic corrosion protection with good aging characteristics and no cracking at low temperatures, due to its combination of raw materials. The dry film adheres well to cleaned underbodies, also to painted surfaces and exhibits a very high abrasionresistance. Painting with standard automotive paints (conventional and water based) is possible under the following conditions:
- allow minimum 16 hours drying of the coating
- apply a fine paint mist prior to final painting
- final painting only after beginning of drying of the pre-paintingsubsequent oven drying at 60°C possible.
Application areas:
TEROSON RB R2000 HS is suitable for repair work on the underbody, wheel house, front and rear aprons, spoilers, door sills, particularly as protection against road stones. The material is used as coating for painted parts or primer surfaced metals on the underbody and for repair works on coatings which are based on rubber/resins. TEROSON RB R2000 HS is also suitable for sound damping of wheel houses and side walls, and for covering and sealing of repair jobs, welding seams and overlaps. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
Pretreatment
Surfaces to be treated with TEROSON RB R2000 HS have to be cleaned well and rust must be removed. The areas must be dry and free of grease, dirt and to a great extent free of dust. Areas not to be coated should be covered with masking paper. In the case of new vehicles, protective wax must be steam-cleaned. If applied to older vehicles, watch out for beginning of rust formation, which has to be removed with a wire brush.
Application
TEROSON RB R2000 HS is applied with the Teroson UBC-Gun from 1-l-cans; application pressure: 4 - 5 bar. Shake the can well up side down for 1 minute before use. Opened containers must not be left open because the material will form a skin. On vertical surfaces, the underbody coating can be applied in one step up to 1 mm layer thickness (wet film). In order to avoid bare patches, the material should be sprayed in criss-cross fashion. Under favourable weather conditions, the vehicle is ready for use 2 - 4 hours afterapplication. For final drying 24 - 48 hours are necessary.
Storage:
Parameters:
Full technical information can be found in technical data sheet