The website uses cookies to provide personalized services at the highest level, including statistical services and to adapt the content to individual preferences of users. Saving cookies can be turned off in your browser settings.
OK
[zamknij]     

TEROSON Bond 60 Controlled Cure - 310ml (Windscreen adhesive, fast)

TEROSON Bond 60 Controlled Cure - 310ml (Windscreen adhesive, fast) (IDH.2700553 )

Product description:
TEROSON® BOND 60 CONTROLLED CURE is a two-component polyurethane adhesive. This windscreen adhesive cures independent from environmental conditions by using a B-component which will be mixed automatically to the A-component during application. The safe drive-away time according to FMVSS 212/208 stays regardless of humidity or temperature at 60 minutes.It has an excellent adhesion to glass, glass with ceramic coating, encapsulation and to painted surfaces in connection with a black primer. Typical applications include the bonding of front, rear and side screens to the body of passenger-, utility-, special- and rail vehicles. Further information about the product: biuro@woronko-kleje.pl

Directions for use:
Priming
1. Before opening the TEROSON® BOND ALL-IN-ONE PRIMER bottle, shake well (at least 1 minute).
2. Apply primer with wool dauber in one pass on the bond line (allow to flash off for 2 minutes).
3. Within the first 2 hours after cutting back the old adhesive bead in the body frame, it does not need to be primed. But if the replacement takes longer than 2 hours, the old cut bead needs to be activated with TEROSON® BOND ALL-IN-ONE PRIMER. NOTE: Provided that it is not contaminated with dust or grease, the old cut adhesive bead is the best adhesive surface for the TEROSON® BOND 60 CONTROLLED CURE adhesive.
4. If windows are bonded which have been pre-coated with a primer or PU–based adhesive/sealant by the glass supplier, TEROSON® BOND ALL-IN-ONE-PRIMER is also suitable to ensure the correct adherence of TEROSON® BOND 60 CONTROLLED CURE to the pre-coating.
5. Using a wool dauber, a thin layer of TEROSON® BOND ALL-IN-ONE-PRIMER is applied to the pre-coating. Allow to flash off for 2 minutes. Subsequently, TEROSON® BOND 60 CONTROLLED CURE is applied as usual, but taking into consideration the layer thickness of the pre-coating.

Application
1. Prior to its use, the cartridge of TEROSON® BOND 60 CONTROLLED CURE must be warmed to above 60°C. There are 2 heating devices which could be used. In the TEROSON® ET CR HEATING BOX 2PC minimum 30 minutes or in the TEROSON® ET CR FC HEATINGBOX 6PC device minimum 60 minutes.
2. After piercing top membrane, the B-component has to be screwed on the cartridge thread and application must be started immediately.
3. For application, we recommend using the dispenser TEROSON® POWERLINE II. Make sure to adjust the working pressure to 9 to 11 bar effective at the cartridge piston!
4. Application should be performed ideally in one continuous bead, if possible.
5. The Safe Drive-Away Time of TEROSON® BOND 60 CONTROLLED CURE must be respected.

Storage:
Store product in the unopened container in a dry location. Storage information may also be indicated on the product container labelling. Optimal Storage: 15 to 25 °C. Storage below 5 °C or greater than 25 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.

Parameters:
  • Technology : polyurethane
  • Chemical type : polyurethane
  • Appearance (uncured) : black
  • Components : two-components – requires mixing
  • Viscosity : paste
  • Cure : two-component
  • Application : windscreen adhesive
  • Environmental temperature at application : 5 to 45 °C
  • Material application temperature : 60 to 70 °C
  • In service temperature : -40 to 90 °C
  • Short exposure (up to 1h) : 120 °C
  • Safe Drive-Away time with airbag:
    - Crash Norm FMVSS 212/208 Crash Test 48 km/h, 100% head-on : 60 minutes
    - Crash Norm New Henkel Crash Test Standard 64 km/h, 40% overlap : 2 hours

    Full technical information can be found in the technical data sheet
  • Assortment