Try to find the solution
LOCTITE PC 7228 - 1kg (epoxy resin with ceramic filler, smooth, white)
No.
IDH.2015129
LOCTITE PC 7228 - 1kg (epoxy resin with ceramic filler, smooth, white)
Product description:
LOCTITE 7228 is an ultra smooth, ceramic reinforced epoxy that provides a high gloss, low friction coating designed to protect against turbulence and abrasion under typical dry service temperatures of -29 °C to 93 °C. Used by itself, LOCTITE 7228 is recommended for sealing and protecting equipment from corrosion and wear. It also works as a top coat over Loctite Nordbak Wearing Compounds for applications requiring surface rebuilding and lasting protection. Typical applications include providing a smooth, protective abrasion resistant coating, repairing heat exchangers and condensers, lining tanks and chutes, resurfacing and repairing rudders and pintel housings, and repairing cooling pump impellers and butterfly valves. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
Surface Preparation
Proper surface preparation is critical to the long-term performance of this product. The exact requirements vary with the severity of the application, expected service life, and initial substrate conditions.
1. Clean, dry and abrade application surface. You can use LOCTITE SF 7063. The more thorough the degree of surface preparation the better the performance of the application. If possible, it is recommended that the surface be grit blasted to a Near White Metal (SSPC-SP10/NACE No. 2) Standard. For less severe applications roughening the surface with hand tools is suitable.
2. Solvent cleaning with a residue-free solvent is recommended as the final step to aid in adhesion.
Mixing
1. Material temperature should be between 20 °C to 30 °C.
2. Add hardener contents to resin. Mix material vigorously until uniform in color. Be sure to mix along the bottom and sides of mixing container. Mix three to five minutes.
Application Method
1. Apply fully mixed material to the prepared surface.
Storage:
Store product in the unopened container in a dry location. Material removed from containers may be contaminated during use. Do not return liquid to original container. Storage information may be indicated on the product container labeling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Henkel cannot assume responsibility for product which has been contaminated or stored under conditions other than those recommended.
Parameters:
Typical properties of cured material:
- Hardness (Shora D): 85
- Compressive strength: 86.2 N/mm²
- Shear strength: 13.6 N/mm²
- Working temperature: from -30 °C to +90 °C
- Color: white, thin liquid
Full technical information is included in the product's technical sheet.
LOCTITE 7228 is an ultra smooth, ceramic reinforced epoxy that provides a high gloss, low friction coating designed to protect against turbulence and abrasion under typical dry service temperatures of -29 °C to 93 °C. Used by itself, LOCTITE 7228 is recommended for sealing and protecting equipment from corrosion and wear. It also works as a top coat over Loctite Nordbak Wearing Compounds for applications requiring surface rebuilding and lasting protection. Typical applications include providing a smooth, protective abrasion resistant coating, repairing heat exchangers and condensers, lining tanks and chutes, resurfacing and repairing rudders and pintel housings, and repairing cooling pump impellers and butterfly valves. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
Surface Preparation
Proper surface preparation is critical to the long-term performance of this product. The exact requirements vary with the severity of the application, expected service life, and initial substrate conditions.
1. Clean, dry and abrade application surface. You can use LOCTITE SF 7063. The more thorough the degree of surface preparation the better the performance of the application. If possible, it is recommended that the surface be grit blasted to a Near White Metal (SSPC-SP10/NACE No. 2) Standard. For less severe applications roughening the surface with hand tools is suitable.
2. Solvent cleaning with a residue-free solvent is recommended as the final step to aid in adhesion.
Mixing
1. Material temperature should be between 20 °C to 30 °C.
2. Add hardener contents to resin. Mix material vigorously until uniform in color. Be sure to mix along the bottom and sides of mixing container. Mix three to five minutes.
Application Method
1. Apply fully mixed material to the prepared surface.
Storage:
Store product in the unopened container in a dry location. Material removed from containers may be contaminated during use. Do not return liquid to original container. Storage information may be indicated on the product container labeling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Henkel cannot assume responsibility for product which has been contaminated or stored under conditions other than those recommended.
Parameters:
- Hardness (Shora D): 85
- Compressive strength: 86.2 N/mm²
- Shear strength: 13.6 N/mm²
- Working temperature: from -30 °C to +90 °C
- Color: white, thin liquid
Full technical information is included in the product's technical sheet.
