Try to find the solution
LOCTITE PC 7230 - 10kg (epoxy resin with coarse ceramic filler, up to 205 °C)
No.
IDH.255896
LOCTITE PC 7230 - 10kg (epoxy resin with coarse ceramic filler, up to 205 °C)
Product description:
Compound is a two-part Ceramic filled epoxy paste designed to protect, rebuild, and repair high wear areas of processing equipment. Temperature range –30° to +230°C. High Temperature Wearing Compound requires post-curing for ultimate performance and temperature resistance. Further information about the product: biuro@woronko-kleje.pl
Advantages:
· Ceramic -filled for outstanding resistance to abrasion
· Renews worn surfaces fast - reduces downtime
· Extends wear life-resists sliding abrasive wear and eliminates costly wear part inventory
· Non sag - provides abrasion resistance on over-head and vertical surfaces
TYPICAL APPLICATIONS:
· Cyclone and separator bodies
· Dust collectors and exhausters
· Pump liners and impellers
· Fan blades and housings
· Chutes and hoppers
· Exhausters
Steps to achieve the best adhesive results:
Surface Preparation
Proper surface preparation is critical to the long-term performance of this product. The exact requirements vary with the severity of the application, expected service life, and initial substrate conditions. Thoroughly clean and abrade surfaces (grit blast if possible), finally clean with LOCTITE SF 7063. The more thorough the degree of surface preparation the better the performance of the application.
On vertical or overhead areas, tack welding expanded metal mesh onto the metal substrate is recommended prior to application of 7230 Wearing Compound.
Mixing
· Measure 4 parts resin to 1 part hardener by volume (3.9 to 1 by weight) or transfer entire kit onto a clean and dry mixing surface and mix together until uniform in colour.
· If resin and hardener temperatures are 15°C or below, preheat resin only to about 30°C but not to exceed 40°C
Application
· Apply fully mixed material to the prepared surface.
· Initially apply as a thin film to “wet” out the surface.
· Build up to desired thickness (minimum 6mm), avoid air entrapment
· At 25°C the working time is 30 minutes. Functional cure time is 7 hours, post cure at 150°C for 2 hours.
Storage:
Product shall be ideally stored in a cool, dry location in unopened containers at a temperature between 8°C to 28°C unless otherwise labelled. Optimal storage is at the lower half of this temperature range. To prevent contamination of unused product, do not return any material to its original container. For further specific shelf life information, contact Loctite UK Technical Service.
Parameters:
Working Life, minutes : 30 Fixture time, hours : Requires Post Cure, See Directions For Use Compressive Strength, ASTM D695,N/mm² : 103,4 Hardness ASTM D-2240, Shore D : 90
Full technical information can be found in the technical data sheet.
Compound is a two-part Ceramic filled epoxy paste designed to protect, rebuild, and repair high wear areas of processing equipment. Temperature range –30° to +230°C. High Temperature Wearing Compound requires post-curing for ultimate performance and temperature resistance. Further information about the product: biuro@woronko-kleje.pl
Advantages:
· Ceramic -filled for outstanding resistance to abrasion
· Renews worn surfaces fast - reduces downtime
· Extends wear life-resists sliding abrasive wear and eliminates costly wear part inventory
· Non sag - provides abrasion resistance on over-head and vertical surfaces
TYPICAL APPLICATIONS:
· Cyclone and separator bodies
· Dust collectors and exhausters
· Pump liners and impellers
· Fan blades and housings
· Chutes and hoppers
· Exhausters
Steps to achieve the best adhesive results:
Surface Preparation
Proper surface preparation is critical to the long-term performance of this product. The exact requirements vary with the severity of the application, expected service life, and initial substrate conditions. Thoroughly clean and abrade surfaces (grit blast if possible), finally clean with LOCTITE SF 7063. The more thorough the degree of surface preparation the better the performance of the application.
On vertical or overhead areas, tack welding expanded metal mesh onto the metal substrate is recommended prior to application of 7230 Wearing Compound.
Mixing
· Measure 4 parts resin to 1 part hardener by volume (3.9 to 1 by weight) or transfer entire kit onto a clean and dry mixing surface and mix together until uniform in colour.
· If resin and hardener temperatures are 15°C or below, preheat resin only to about 30°C but not to exceed 40°C
Application
· Apply fully mixed material to the prepared surface.
· Initially apply as a thin film to “wet” out the surface.
· Build up to desired thickness (minimum 6mm), avoid air entrapment
· At 25°C the working time is 30 minutes. Functional cure time is 7 hours, post cure at 150°C for 2 hours.
Storage:
Product shall be ideally stored in a cool, dry location in unopened containers at a temperature between 8°C to 28°C unless otherwise labelled. Optimal storage is at the lower half of this temperature range. To prevent contamination of unused product, do not return any material to its original container. For further specific shelf life information, contact Loctite UK Technical Service.
Parameters:
Full technical information can be found in the technical data sheet.
