Try to find the solution
LOCTITE FREKOTE FMS - 1L (mold sealant)
No.
IDH.381038
Price
LOCTITE FREKOTE FMS - 1L (mold sealant)
Product description:
LOCTITE FREKOTE FMS is formulated specifically as a sealer for fiberglass reinforced polyester, epoxy and other composite molds commonly used in the fiberglass molding industry. LOCTITE FREKOTE FMS must be used when using green, or new, molds with microporosity and other slight surface imperfections. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. Apply LOCTITE FREKOTE FMS with a clean, lint free, cotton wiping cloth. Wet the cloth with LOCTITE FREKOTE FMS until it is damp but not dripping.
2. Wipe a smooth, wet film over the entire mold surface. For larger molds, apply LOCTITE FREKOTE FMS to the surface one section at a time starting at one end and working towards the other. Using a clean cloth, wipe off the area that was just treated to obtain a smooth thin wet layer.
3. Allow a minimum of 15 minutes before applying next coat. New molds require 1 to 2 coats of sealer.
4. NOTE: Changes in temperature will affect solvent dry time. At temperatures below 18°C, waiting time between wiping on and drying off can be slightly longer than 20 seconds. At higher then normal temperatures (greater then 35°C) the wait time is significantly reduced and can be as quick as 1 to 2 seconds. In these conditions it is also advisable to reduce your wipe area to eliminate streaking due to the increased solvent evaporation and polymer cure times. A general guideline is to wait until the edges of the wiped area begins to creep inwards indicating the evaporation has just begun. Wipe from the outside and slowly work your way towards the center. Light hand pressure is all that is needed. No hard rubbing required. change cloth frequently to ensure proper drying of the mold. On small molds, allow up to 15 minutes between coats. If one coat takes more than 15 minutes, simply go back to starting point and begin to apply next coat.
5. Allow the final coat to cure for 20 minutes at 20°C.
Storage:
The product is classified as flammable and must be stored in an appropriate manner in compliance with relevant regulations. Do not store near oxidizing agents or combustible materials. Store product in the unopened container in a dry location. Storage information may also be indicated on the product container labelling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Appearance : clear, colorless Chemical type : solvent based polymer Odor : hydrocarbon Application temperature : 13 to 35 °C High gloss : finish
-Easy application
-Fast curing
-Eliminates Porosity/Microporosity
-Seals "green" molds and repaired areas
Full technical information can be found in the technical data sheet
LOCTITE FREKOTE FMS is formulated specifically as a sealer for fiberglass reinforced polyester, epoxy and other composite molds commonly used in the fiberglass molding industry. LOCTITE FREKOTE FMS must be used when using green, or new, molds with microporosity and other slight surface imperfections. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. Apply LOCTITE FREKOTE FMS with a clean, lint free, cotton wiping cloth. Wet the cloth with LOCTITE FREKOTE FMS until it is damp but not dripping.
2. Wipe a smooth, wet film over the entire mold surface. For larger molds, apply LOCTITE FREKOTE FMS to the surface one section at a time starting at one end and working towards the other. Using a clean cloth, wipe off the area that was just treated to obtain a smooth thin wet layer.
3. Allow a minimum of 15 minutes before applying next coat. New molds require 1 to 2 coats of sealer.
4. NOTE: Changes in temperature will affect solvent dry time. At temperatures below 18°C, waiting time between wiping on and drying off can be slightly longer than 20 seconds. At higher then normal temperatures (greater then 35°C) the wait time is significantly reduced and can be as quick as 1 to 2 seconds. In these conditions it is also advisable to reduce your wipe area to eliminate streaking due to the increased solvent evaporation and polymer cure times. A general guideline is to wait until the edges of the wiped area begins to creep inwards indicating the evaporation has just begun. Wipe from the outside and slowly work your way towards the center. Light hand pressure is all that is needed. No hard rubbing required. change cloth frequently to ensure proper drying of the mold. On small molds, allow up to 15 minutes between coats. If one coat takes more than 15 minutes, simply go back to starting point and begin to apply next coat.
5. Allow the final coat to cure for 20 minutes at 20°C.
Storage:
The product is classified as flammable and must be stored in an appropriate manner in compliance with relevant regulations. Do not store near oxidizing agents or combustible materials. Store product in the unopened container in a dry location. Storage information may also be indicated on the product container labelling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
-Easy application
-Fast curing
-Eliminates Porosity/Microporosity
-Seals "green" molds and repaired areas
Full technical information can be found in the technical data sheet
