Try to find the solution
LOCTITE EA 9497 - 50ml (gray epoxy adhesive, up to 180 °C)
No.
IDH.2053807
Price
Associated products:
- LOCTITE SF 7063 - 400ml (degreasing agent for plastics and metals) spray (IDH.2385316)
- TEROSON ET QUAD ST MIX SMALL (for 50 ml cartridges 1:1, 1:2) (IDH.2900614)
- LOCTITE EA 9497 - 400ml (two-component epoxy adhesive, gray, up to 180°C) (IDH.2053833)
- LOCTITE 96001 (manual applicator for 50ml cartridges, mixing ratio of components A&B 1:1 or 1:2) (IDH.267452)
LOCTITE EA 9497 - 50ml (gray epoxy adhesive, up to 180 °C)
Associated products:
- LOCTITE SF 7063 - 400ml (degreasing agent for plastics and metals) spray (IDH.2385316)
- TEROSON ET QUAD ST MIX SMALL (for 50 ml cartridges 1:1, 1:2) (IDH.2900614)
- LOCTITE EA 9497 - 400ml (two-component epoxy adhesive, gray, up to 180°C) (IDH.2053833)
- LOCTITE 96001 (manual applicator for 50ml cartridges, mixing ratio of components A&B 1:1 or 1:2) (IDH.267452)
Product description:
LOCTITE EA 9497 is a medium viscosity, two component, room temperature curing epoxy adhisive that bonds a wide variety of materials making it suitable as a general purpose adhesive. LOCTITE EA 9497 is ideal for heat dissipation applications such as bonding metal sheets for high heat transfer and potting electrical components. It is good for high compression strength applications, as well as high Tg applications with demanding hot strength requirements. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. For best performance surfaces for bonding should be clean, dry and free of grease. Use LOCTITE SF 7063. For high strength structural bonds, special surface treatments can increase the bond strength and durability.
2. To use, resin and hardener must be blended. Using bulk containers, mix thoroughly by weight or volume in the proportions specified in the Product Description Matrix. For hand mixing, weigh or measure out the desired amount of resin and hardener and mix thoroughly. Mixapproximately 15 seconds after uniform color is obtained.
3. Do not mix quantities greater than 4 kg in mass as excessive heat build-up can occur. Mixing smaller quantities will minimize the heat build-up.
4. Apply the adhesive as quickly as possible after mixing to one surface to be joined. For maximum bond strength apply adhesive evenly to both surfaces. Parts should be assembled immediately after mixed adhesive has been applied.
5. Working life of the mixed adhesive is 3 to 4 hours in 22 °C. Higher temperature and larger quantities will shorten this working time.
6. Keep the assembled parts from moving during cure. The joint should be allowed to develop full strength before subjecting to any service loads.
7. Excess uncured adhesive can be wiped away with organic solvent (e.g. Acetone).
8. After use and before adhesive hardens, mixing and application equipment should be cleaned with hot soapy water.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Cured for 7 days in temperature 22°C. Shear strength, ISO4587:Carbon steel, N/mm² : 20 Stainless steel, N/mm² : 9 Aluminum, N/mm² : 7 Aluminum (szlifowane), N/mm² : 15 Brass, N/mm² : 5 Cooper, N/mm² : 5 Zinc dichromate, N/mm² : 5 ABS, N/mm² : 6 Polycarbonate, N/mm² : 4 PMMA, N/mm² : 1 Glass fiber reinforced epoxy, N/mm² : 8 Wood hard (Teak), N/mm² : 12 Wood soft miękkie, N/mm² : 8
Full technical information can be found in the technical data sheet
LOCTITE EA 9497 is a medium viscosity, two component, room temperature curing epoxy adhisive that bonds a wide variety of materials making it suitable as a general purpose adhesive. LOCTITE EA 9497 is ideal for heat dissipation applications such as bonding metal sheets for high heat transfer and potting electrical components. It is good for high compression strength applications, as well as high Tg applications with demanding hot strength requirements. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. For best performance surfaces for bonding should be clean, dry and free of grease. Use LOCTITE SF 7063. For high strength structural bonds, special surface treatments can increase the bond strength and durability.
2. To use, resin and hardener must be blended. Using bulk containers, mix thoroughly by weight or volume in the proportions specified in the Product Description Matrix. For hand mixing, weigh or measure out the desired amount of resin and hardener and mix thoroughly. Mixapproximately 15 seconds after uniform color is obtained.
3. Do not mix quantities greater than 4 kg in mass as excessive heat build-up can occur. Mixing smaller quantities will minimize the heat build-up.
4. Apply the adhesive as quickly as possible after mixing to one surface to be joined. For maximum bond strength apply adhesive evenly to both surfaces. Parts should be assembled immediately after mixed adhesive has been applied.
5. Working life of the mixed adhesive is 3 to 4 hours in 22 °C. Higher temperature and larger quantities will shorten this working time.
6. Keep the assembled parts from moving during cure. The joint should be allowed to develop full strength before subjecting to any service loads.
7. Excess uncured adhesive can be wiped away with organic solvent (e.g. Acetone).
8. After use and before adhesive hardens, mixing and application equipment should be cleaned with hot soapy water.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Cured for 7 days in temperature 22°C. Shear strength, ISO4587:
Full technical information can be found in the technical data sheet
