Try to find the solution
LOCTITE FREKOTE B15 - 1L (sealant for molds)
No.
IDH.381021
Price
LOCTITE FREKOTE B15 - 1L (sealant for molds)
Product description:
Loctite Frekote® B-15 is formulated specifically as a sealer for composite and metal molds with micro porosity problems, small surface scratches or imperfections. Used in conjunction with other Frekote® products, Loctite® Frekote® B-15™ provides an excellent base coat enhancing the release advantages offered. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. Loctite® Frekote® B-15 can be applied to mold surfaces by spraying, brushing, dipping or wiping with a clean, lint free, cotton wiping cloth. When spraying, ensure a dry air source is used or use an airless spray system making sure the nozzles is 20 to 25 cm from the mold surface.
2. Brushing and dipping are effective methods of application, but care should be taken to avoid excessive pooling andto ensure that the part is well drained. Wiping on is the best method of application.
3. Only a thin wet film is required. It is suggested that small areas be coated, working progressively from one mold to the other.
4. Apply a minimum of two coats, allowing 30 minutes between coats.
5. The final coat will cure within 24 hours at 23°C or the cure process can be shortened by baking the mold for 60 minutes at 95°C after ensuring that the mold is dry and all sovents have flashed off.
6. The mold is now ready to be coated with Frekote mold release products. Please refer to individual product data sheets for the proper application of the release agent.
Storage:
The product is classified as flammable and must be stored in an appropriate manner in compliance with relevant regulations. Do not store near oxidizing agents or combustible materials. Store product in the unopened container in a dry location. Storage information may also be indicated on the product container labelling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Technology: Mold Sealer Appearance: Clear, colorless Chemical Type: Solvent Based Polymer Odor: Solvent Cure: Room temperature cure Cured: Thermal Stability ≤400 °C Application: Mold Sealer Application Temperature: 20 to 60 °C Specific Benefit:
- No contaminating transfer
- High thermal stability
- Seals mold porosity, scratches or imperfections
Full technical information can be found in the technical data sheet
Loctite Frekote® B-15 is formulated specifically as a sealer for composite and metal molds with micro porosity problems, small surface scratches or imperfections. Used in conjunction with other Frekote® products, Loctite® Frekote® B-15™ provides an excellent base coat enhancing the release advantages offered. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. Loctite® Frekote® B-15 can be applied to mold surfaces by spraying, brushing, dipping or wiping with a clean, lint free, cotton wiping cloth. When spraying, ensure a dry air source is used or use an airless spray system making sure the nozzles is 20 to 25 cm from the mold surface.
2. Brushing and dipping are effective methods of application, but care should be taken to avoid excessive pooling andto ensure that the part is well drained. Wiping on is the best method of application.
3. Only a thin wet film is required. It is suggested that small areas be coated, working progressively from one mold to the other.
4. Apply a minimum of two coats, allowing 30 minutes between coats.
5. The final coat will cure within 24 hours at 23°C or the cure process can be shortened by baking the mold for 60 minutes at 95°C after ensuring that the mold is dry and all sovents have flashed off.
6. The mold is now ready to be coated with Frekote mold release products. Please refer to individual product data sheets for the proper application of the release agent.
Storage:
The product is classified as flammable and must be stored in an appropriate manner in compliance with relevant regulations. Do not store near oxidizing agents or combustible materials. Store product in the unopened container in a dry location. Storage information may also be indicated on the product container labelling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
- No contaminating transfer
- High thermal stability
- Seals mold porosity, scratches or imperfections
Full technical information can be found in the technical data sheet
