LOCTITE 414 - 20g (cyanoacrylate (instant) adhesive, colorless/transparent)
No.
IDH.1922832
Product description:
LOCTITE® 414 is a general purpose cyanoacrylate instant adhesive. LOCTITE® 414 has been qualified to Commercial Item Description A-A-3097. Note: This is a regional approval. Please contact your local Technical Service Center for more information and clarification. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. For best performance bond surfaces should be clean and free from grease.
2. This product performs best in thin bond gaps (0.05 mm).
3. Excess adhesive can be dissolved with Loctite cleanup solvents, nitromethane or acetone.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.Optimal Storage: 2 °C to 8 °C. Storage below 2 °C or greater than 8 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:Fixture Time, seconds:
- Steel (degreased) : 15 to 30
- Aluminum : 2 to 10
- Neoprene : <5
- Rubber, nitrile : <5
- ABS : 2 to 10
- PVC : 2 to 10
- Polycarbonate : 15 to 50
- Phenolic : 5 to 15 Lap Shear Strength, ISO 4587 (after 24 hours at 22 °C):
- Steel (grit blasted) N/mm² :18 to 26
- Aluminum (etched) N/mm² : 11 to 19
- ABS N/mm² : >6
- PVC N/mm² : >4
- Polycarbonate N/mm² : >5
- Phenolic N/mm² : 5 to 15
- Neoprene N/mm² : >10
- Nitrile N/mm² : >10 Tensile Strength, ISO 6922:
- Steel (grit blasted) N/mm² : 12 to 25
Further information can be found in technical data sheet
LOCTITE® 414 is a general purpose cyanoacrylate instant adhesive. LOCTITE® 414 has been qualified to Commercial Item Description A-A-3097. Note: This is a regional approval. Please contact your local Technical Service Center for more information and clarification. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. For best performance bond surfaces should be clean and free from grease.
2. This product performs best in thin bond gaps (0.05 mm).
3. Excess adhesive can be dissolved with Loctite cleanup solvents, nitromethane or acetone.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.Optimal Storage: 2 °C to 8 °C. Storage below 2 °C or greater than 8 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
- Steel (degreased) : 15 to 30
- Aluminum : 2 to 10
- Neoprene : <5
- Rubber, nitrile : <5
- ABS : 2 to 10
- PVC : 2 to 10
- Polycarbonate : 15 to 50
- Phenolic : 5 to 15
- Steel (grit blasted) N/mm² :18 to 26
- Aluminum (etched) N/mm² : 11 to 19
- ABS N/mm² : >6
- PVC N/mm² : >4
- Polycarbonate N/mm² : >5
- Phenolic N/mm² : 5 to 15
- Neoprene N/mm² : >10
- Nitrile N/mm² : >10
- Steel (grit blasted) N/mm² : 12 to 25
Further information can be found in technical data sheet