LOCTITE 222 - 250ml (anaerobic, violet, low strength threadlocker)
No.
IDH.245636
Associated products:
- LOCTITE 222 - 50ml (anaerobic, violet, low strength threadlocker) (IDH.245635)
- LOCTITE Pro Pump Handheld Dispenser for bottles 50ml & 250ml (IDH.2564842)
- LOCTITE SF 7063 - 400ml (degreasing agent for plastics and metals) spray (IDH.2385316)
- LOCTITE 222 - 10ml (anaerobic, violet, low strength threadlocker) (IDH.245633)
LOCTITE 222 - 250ml (anaerobic, violet, low strength threadlocker)
Associated products:
- LOCTITE 222 - 50ml (anaerobic, violet, low strength threadlocker) (IDH.245635)
- LOCTITE Pro Pump Handheld Dispenser for bottles 50ml & 250ml (IDH.2564842)
- LOCTITE SF 7063 - 400ml (degreasing agent for plastics and metals) spray (IDH.2385316)
- LOCTITE 222 - 10ml (anaerobic, violet, low strength threadlocker) (IDH.245633)
Product description:
LOCTITE 222 is designed for the locking and sealing of threaded fasteners which require easy disassembly with standard hand tools. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. Particularly suitable for applications such as adjustment of set screws, small diameter or long engagement lengthfasteners, where easy disassembly is required without shearing the screw.
The thixotropic nature of LOCTITE 222 reduces the migration of liquid product after application to the substrate.
Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
FOR ASSEMBLY:
1. For best results, clean all surfaces (external and internal) with a LOCTITE SF 7063 cleaning solvent and allow to dry.
2. If the material is an inactive metal or the cure speed is too slow, spray all threads with activator LOCTITE SF 7649 or LOCTITE 7471 and allow to dry.
3. Shake the product thoroughly before use.
4. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application.
5. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area.
6. For Blind Holes, apply several drops of the product down the internal threads to the bottom of the hole.
7. Assemble and tighten as required.
8. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thouroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also.
FOR DISASSEMBLY:
1. Remove with standard hand tools.
2. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot.
FOR CLEAN UP:
1. Cured product can be removed with a combination of soaking in a LOCTITE SF 7200 solvent and mechanical abrasion such as a wire brush.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Full information can be found on the technical sheet of the product.
LOCTITE 222 is designed for the locking and sealing of threaded fasteners which require easy disassembly with standard hand tools. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. Particularly suitable for applications such as adjustment of set screws, small diameter or long engagement lengthfasteners, where easy disassembly is required without shearing the screw.
The thixotropic nature of LOCTITE 222 reduces the migration of liquid product after application to the substrate.
Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
FOR ASSEMBLY:
1. For best results, clean all surfaces (external and internal) with a LOCTITE SF 7063 cleaning solvent and allow to dry.
2. If the material is an inactive metal or the cure speed is too slow, spray all threads with activator LOCTITE SF 7649 or LOCTITE 7471 and allow to dry.
3. Shake the product thoroughly before use.
4. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application.
5. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area.
6. For Blind Holes, apply several drops of the product down the internal threads to the bottom of the hole.
7. Assemble and tighten as required.
8. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thouroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also.
FOR DISASSEMBLY:
1. Remove with standard hand tools.
2. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot.
FOR CLEAN UP:
1. Cured product can be removed with a combination of soaking in a LOCTITE SF 7200 solvent and mechanical abrasion such as a wire brush.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
- Thread size: to M36
- Strength : low
- Time to get full strength (22 °C):
-Steel : 6 hours
-Stainless steel : 24 hours
-Brass : 1 hour
-Zinc dichromate : 24 hours - Time to obtain initial strength (22 °C):
-Steel : 20 minutes
-Stainless steel : 6 hours
-Brass : 10 miutes.
-Zinc dichromate : 2 hours - Breakaway Torque for nuts M10 : 6 Nm
- Prevail Torque: 4 Nm
- Working temperature : from -55 °C to +150 °C
- Color : violet
Full information can be found on the technical sheet of the product.