LOCTITE AA 319 - 0,5 ml (adhesive kit for rearview mirror)
No.
IDH.195908
Product description:
LOCTITE® AA 319 typical applications include bonding materials such as metals, glass, ceramics or plastics. The product cures when confined between close fitting parts with the aid of Activator LOCTITE 7649. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. For best performance bond surfaces should be clean and free from grease.
2. To ensure a fast and reliable cure, Activator LOCTITE SF 7649 should be applied to one of the bond surfaces and the adhesive to the other surface. Parts should be assembled within 15 minutes.
3. The recommended bondline gap is 0.1 mm. Where bond gaps are large (up to a maximum of 0.5 mm), or faster cure speed is required, Activator LOCTITE SF 7649 should be applied to both surfaces.Parts should be assembled immediately (within 1 minute).
4. Excess adhesive can be wiped away with organic solvent.
5. Bond should be held clamped until adhesive has fixtured.
6. Product should be allowed to develop full strength before subjecting to any service loads (typically 24 to 72 hours afterassembly, depending on bond gap, materials and ambient conditions)
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:Coefficient of Thermal Expansion, ISO 11359-2, K -1 : 100×10-6 Coefficient of Thermal Conductivity, ISO 8302, W/(m·K) : 0.1 Specific Heat, kJ/(kg·K) : 0.3 After 1 hour at 22 °C, Activator 7649 on 2 sides:
- Lap Shear Strength, ISO 4587: Steel (grit blasted) N/mm² ≥10.3
Full technical information can be found in technical data sheet
LOCTITE® AA 319 typical applications include bonding materials such as metals, glass, ceramics or plastics. The product cures when confined between close fitting parts with the aid of Activator LOCTITE 7649. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. For best performance bond surfaces should be clean and free from grease.
2. To ensure a fast and reliable cure, Activator LOCTITE SF 7649 should be applied to one of the bond surfaces and the adhesive to the other surface. Parts should be assembled within 15 minutes.
3. The recommended bondline gap is 0.1 mm. Where bond gaps are large (up to a maximum of 0.5 mm), or faster cure speed is required, Activator LOCTITE SF 7649 should be applied to both surfaces.Parts should be assembled immediately (within 1 minute).
4. Excess adhesive can be wiped away with organic solvent.
5. Bond should be held clamped until adhesive has fixtured.
6. Product should be allowed to develop full strength before subjecting to any service loads (typically 24 to 72 hours afterassembly, depending on bond gap, materials and ambient conditions)
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
- Lap Shear Strength, ISO 4587: Steel (grit blasted) N/mm² ≥10.3
Full technical information can be found in technical data sheet