LOCTITE 542 - 250ml (anaerobic, brown, medium strength thread sealant)
No.
IDH.246614
Associated products:
- LOCTITE 542 - 50ml (anaerobic, brown, medium strength thread sealant) (IDH.246613)
- LOCTITE Pro Pump Handheld Dispenser for bottles 50ml & 250ml (IDH.2564842)
- LOCTITE SF 7063 - 400ml (degreasing agent for plastics and metals) spray (IDH.2385316)
- LOCTITE 542 - 10ml (anaerobic thread sealant, medium strength, brown) (IDH.246608)
LOCTITE 542 - 250ml (anaerobic, brown, medium strength thread sealant)
Associated products:
- LOCTITE 542 - 50ml (anaerobic, brown, medium strength thread sealant) (IDH.246613)
- LOCTITE Pro Pump Handheld Dispenser for bottles 50ml & 250ml (IDH.2564842)
- LOCTITE SF 7063 - 400ml (degreasing agent for plastics and metals) spray (IDH.2385316)
- LOCTITE 542 - 10ml (anaerobic thread sealant, medium strength, brown) (IDH.246608)
Product description:
LOCTITE 542 is designed for the locking and sealing of metal pipes and fittings. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the substrate. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
FOR ASSEMBLY:
1. For best results, clean all surfaces (external and internal) with a LOCTITE SF 7063 cleaning solvent and allow to dry.
2. If the material is an inactive metal or the cure speed is to slow, spray all threads with activator LOCTITE SF 7471 or LOCTITE SF 7649 and allow to dry.
3. Apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thouroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also.
4. Using accepted trade practices, assemble and wrench tighten fittings until proper alignment is obtained.
5. Properly tightened fittings will seal instantly to moderate pressures. For maximum pressure resistance and solvent resistance allow the product to cure a minimum of 24 hours.
FOR DISASSEMBLY:
1. Remove with standard hand tools.
2. Where hand tools do not work because of excessive engagement length or large diameters (over 1"), apply localized heat to approximately 250°C. Disassemble while hot.
FOR CLEAN UP:
1. Cured product can be removed with a combination of soaking in a LOCTITE SF 7200 solvent and mechanical abrasion such as a wire brush.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Full information can be found on the technical data sheet.
LOCTITE 542 is designed for the locking and sealing of metal pipes and fittings. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the substrate. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
FOR ASSEMBLY:
1. For best results, clean all surfaces (external and internal) with a LOCTITE SF 7063 cleaning solvent and allow to dry.
2. If the material is an inactive metal or the cure speed is to slow, spray all threads with activator LOCTITE SF 7471 or LOCTITE SF 7649 and allow to dry.
3. Apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thouroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also.
4. Using accepted trade practices, assemble and wrench tighten fittings until proper alignment is obtained.
5. Properly tightened fittings will seal instantly to moderate pressures. For maximum pressure resistance and solvent resistance allow the product to cure a minimum of 24 hours.
FOR DISASSEMBLY:
1. Remove with standard hand tools.
2. Where hand tools do not work because of excessive engagement length or large diameters (over 1"), apply localized heat to approximately 250°C. Disassemble while hot.
FOR CLEAN UP:
1. Cured product can be removed with a combination of soaking in a LOCTITE SF 7200 solvent and mechanical abrasion such as a wire brush.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
- The rate of cure will depend on the substrate used:
-Brass : 6 minutes
-Steel :15 minutes
-Stainless steel : 6 hours
-Zinc dichromate : 1 hour - The rate of cure will depend on the bondline gap:
0,05 mm : 10 minutes
0,15 mm : 1,5 hours
0,25 mm : 6 hours - Working temperature: from -55 °C to 150 °C.
- Chemical resistance (% initial strength after 500 hours):
-Engine oil : 100%
-Unleaded petrol : 100%
-Brake fluid : 100%
-Ethanol : 100%
-Acetone : 80%
-Water / glycol (50/50%) : 90% - Color: red
Full information can be found on the technical data sheet.
