LOCTITE 272 - 50ml (anaerobic, red-orange, high strength threadlocker)
No.
IDH.1008095
Product description:
LOCTITE 272 is designed for the permanent locking and sealing of threaded fasteners. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. Typical applications include the locking and sealing of large bolts and studs (M25 and larger). This product is not recommended for use in pure oxygenand/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
FOR ASSEMBLY:
1. For best results, clean all surfaces (external and internal) with a LOCTITE SF 7063 cleaning solvent and allow to dry.
2. If the material is an inactive metal or the cure speed is too slow, spray all threads with activator LOCTITE SF 7471 or LOCTITE SF 7649 and allow to dry.
3. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application.
4. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area.
5. For Blind Holes, apply several drops of the product down the internal threads to the bottom of the hole.
6. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thouroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also.
7. Assemble and tighten as required.
FOR DISASSEMBLY:
8. Apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot.
FOR CLEAN UP:
9. Cured product can be removed by soaking in a Loctite solvent, e.g. LOCTITE SF 7200 and mechanical removal with a soft scraper. Avoid formation of dust and aerosols. Complete the cleaning process by wiping with a soft cloth dampened with Loctite Cleaner, e.g. LOCTITE SF 7063 or LOCTITE ODC-free cleaner.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Full technical information can be found in the technical data sheet.
LOCTITE 272 is designed for the permanent locking and sealing of threaded fasteners. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. Typical applications include the locking and sealing of large bolts and studs (M25 and larger). This product is not recommended for use in pure oxygenand/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
FOR ASSEMBLY:
1. For best results, clean all surfaces (external and internal) with a LOCTITE SF 7063 cleaning solvent and allow to dry.
2. If the material is an inactive metal or the cure speed is too slow, spray all threads with activator LOCTITE SF 7471 or LOCTITE SF 7649 and allow to dry.
3. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application.
4. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area.
5. For Blind Holes, apply several drops of the product down the internal threads to the bottom of the hole.
6. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thouroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also.
7. Assemble and tighten as required.
FOR DISASSEMBLY:
8. Apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot.
FOR CLEAN UP:
9. Cured product can be removed by soaking in a Loctite solvent, e.g. LOCTITE SF 7200 and mechanical removal with a soft scraper. Avoid formation of dust and aerosols. Complete the cleaning process by wiping with a soft cloth dampened with Loctite Cleaner, e.g. LOCTITE SF 7063 or LOCTITE ODC-free cleaner.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
- Thread size : to M36
- Strength : high
- Breakaway Torque (M10 nuts): 23 Nm
- Prevail Torque : 25 Nm
- Work temperature: from -55 °C to +200 °C
- Color: red
Full technical information can be found in the technical data sheet.