TEROSON WX 970 - 1l (anticorrosive agent for vehicle underbodies)
No.
IDH.794862
TEROSON WX 970 - 1l (anticorrosive agent for vehicle underbodies)
Product description:
TEROSON WX 970 is a solvent containing, bitumen free anticorrosive agent based on wax, polymers and anticorrosive additives. The product is applied with the Teroson UBC-Gun from 1 l cans, but can also be airless sprayed from drums. Due to its excellent sag resistance, the material can be applied up to a layer thickness of approx. 1 mm.
Application Areas:
TEROSON WX 970 is primarily used on vehicle underbodies, particularly for the treatment of all protective coatings, like those based on PVC, PVC/wax, bitumen/rubber and rubber/resins.
Directions for use:
Pretreatment:
Surfaces to be treated with TEROSON WX 970 have to be cleaned well and rust must be removed. The areas must be dry and free of grease, dirt and to a great extent free of dust. TEROSON WX 970 may only be applied to dry surfaces. Coating materials based on resin/wax can lead to adhesion and compatibility problems with TEROSON WX 970. Therefore, if applied to new vehicles, the underbody has to be steam jet cleaned from protection wax, or compatibility has to be assured by a test application. If applied to older vehicles, first remove existing rust with a wire brush.
Application:
The vehicle underbody should not be too cold in order to assure good spreading and good adhesion of the sprayed material. Temperature of material and underbody should be the same, not less than 15°C.
General:
On vertical surfaces, the underbody coating can be applied in one step. In order to avoid bare patches the material should be sprayed in criss-cross fashion. After drying over night the vehicle is ready for use again. For final drying 24 - 48 hours are necessary.
Storage: Frost sensitive : yes Recommended storage temperature : 10 to 25 °C Shelf life : 24 months
Parameters:
Colour : anthracite Odour : characteristic odour, like wax, mild Consistency : thick-flowing, thixotropic 1 L Can
- Density : approx. 0.86 g/cm³
- Solids : 48 %
- Viscosity : approx. 250 mPa.s
- Equipment : Rheomat 15
- Measuring system : A Drum
- Density : approx. 0.87 g/cm³
- Solids : 50 %
- Viscosity : approx. 350 mPa.s
- Equipment : Rheomat 15
- Measuring system : A Behaviour in the cold : no cracking, no flaking off Storage : 8 hrs -25 °C Mandrel : 70 mm Ø Corrosion resistance salt spray test to DIN 50021 (dry film 50 μm) : min 400 hrs. without rust Climate test DIN 50017-KK (dry film 50 μm) : min 400 hrs. without rust Application temperature : 15 to 25 °C In service temperature : -25 to 80 °C Short exposure (up to 1 h) : 100 °C
Further information about product can be found in Technical Data Sheet
TEROSON WX 970 is a solvent containing, bitumen free anticorrosive agent based on wax, polymers and anticorrosive additives. The product is applied with the Teroson UBC-Gun from 1 l cans, but can also be airless sprayed from drums. Due to its excellent sag resistance, the material can be applied up to a layer thickness of approx. 1 mm.
Application Areas:
TEROSON WX 970 is primarily used on vehicle underbodies, particularly for the treatment of all protective coatings, like those based on PVC, PVC/wax, bitumen/rubber and rubber/resins.
Directions for use:
Pretreatment:
Surfaces to be treated with TEROSON WX 970 have to be cleaned well and rust must be removed. The areas must be dry and free of grease, dirt and to a great extent free of dust. TEROSON WX 970 may only be applied to dry surfaces. Coating materials based on resin/wax can lead to adhesion and compatibility problems with TEROSON WX 970. Therefore, if applied to new vehicles, the underbody has to be steam jet cleaned from protection wax, or compatibility has to be assured by a test application. If applied to older vehicles, first remove existing rust with a wire brush.
Application:
The vehicle underbody should not be too cold in order to assure good spreading and good adhesion of the sprayed material. Temperature of material and underbody should be the same, not less than 15°C.
General:
On vertical surfaces, the underbody coating can be applied in one step. In order to avoid bare patches the material should be sprayed in criss-cross fashion. After drying over night the vehicle is ready for use again. For final drying 24 - 48 hours are necessary.
Storage:
Parameters:
- Density : approx. 0.86 g/cm³
- Solids : 48 %
- Viscosity : approx. 250 mPa.s
- Equipment : Rheomat 15
- Measuring system : A
- Density : approx. 0.87 g/cm³
- Solids : 50 %
- Viscosity : approx. 350 mPa.s
- Equipment : Rheomat 15
- Measuring system : A
Further information about product can be found in Technical Data Sheet
