LOCTITE MR 5921 - 200ml (fast drying, solvent-based, rubber-modified sealant, reddish brown)
No.
IDH.142272
LOCTITE MR 5921 - 200ml (fast drying, solvent-based, rubber-modified sealant, reddish brown)
Product description:
LOCTITE MR 5921 is a reddish brown, viscous, fast drying paste that changes to a hard, semi flexible seal through solvent evaporation. It seals flanges, fittings, connections and assemblies against leakage. Typical applications include freeze plugs, industrial sealant for permanent assemblies, threaded connections, manifold gaskets, air ducts, boilers, pipe fittings and plumbing connections. This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected asa sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Safety Data Sheet (SDS). Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. Remove all previous material from mating surfaces.
2. For best results, clean and dry all surfaces with a residuefree solvent.
3. Remove cap, puncture tube (using self-piercing cap) or cartridge seal and attach extension nozzle (if provided).
4. When used as a gasket dressing, spread product with a spatula to a uniform film on one side of gasket and then position it on the assembly. Coat the second side of gasket and re-assemble.
5. Assembly is operational after 2 hours, full cure is effective after 24 hours.
FOR CLEAN UP:
6. LOCTITE MR 5921 can be removed from metal surfaces with isopropanol. If the sealant has been dried for a long time or at high temperatures, cover the sealant with alcohol and allow to soften overnight.
7. Clean hands with hand cleaners.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Full technical information can be found in the technical data sheet.
LOCTITE MR 5921 is a reddish brown, viscous, fast drying paste that changes to a hard, semi flexible seal through solvent evaporation. It seals flanges, fittings, connections and assemblies against leakage. Typical applications include freeze plugs, industrial sealant for permanent assemblies, threaded connections, manifold gaskets, air ducts, boilers, pipe fittings and plumbing connections. This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected asa sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Safety Data Sheet (SDS). Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. Remove all previous material from mating surfaces.
2. For best results, clean and dry all surfaces with a residuefree solvent.
3. Remove cap, puncture tube (using self-piercing cap) or cartridge seal and attach extension nozzle (if provided).
4. When used as a gasket dressing, spread product with a spatula to a uniform film on one side of gasket and then position it on the assembly. Coat the second side of gasket and re-assemble.
5. Assembly is operational after 2 hours, full cure is effective after 24 hours.
FOR CLEAN UP:
6. LOCTITE MR 5921 can be removed from metal surfaces with isopropanol. If the sealant has been dried for a long time or at high temperatures, cover the sealant with alcohol and allow to soften overnight.
7. Clean hands with hand cleaners.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
- Chemical type : modified resin, fillers and alcohol
- Appearance : red-brown paste
- Smell : alcohol
- Specific gravity : 1,5
- Viscosity : consistency similar to molasses
- Resistant to petrol, oils and cooling agents
- Working temperature : from -50 °C to +204 °C
Full technical information can be found in the technical data sheet.
