LOCTITE 4305 - 20g (cyanoacrylate adhesive (instant), with additional UV curing system)
No.
IDH.456621
LOCTITE 4305 - 20g (cyanoacrylate adhesive (instant), with additional UV curing system)
Product description:
LOCTITE® 4305 is designed for bonding applications that require very rapid fixturing, fillet cure or surface cure. The UV light cure properties facilitate rapid curing of exposed surface areas thereby minimizing blooming and providing an alternative to solvent borne accelerators. Suitable for use in the assembly of disposable medical devices. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. This product is light sensitive; exposure to daylight, UV light and artificial lighting should be kept to a minimum during storage and handling.
2. For best performance bond surfaces should be clean and free from grease.
3. This product performs best in thin bond gaps (0.05 mm).
4. Excess adhesive can be dissolved with Loctite cleanup solvents, nitromethane or acetone
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.Optimal Storage: 2 °C to 8 °C. Storage below 2 °C or greater than 8 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:Block Shear Strength, ISO 13445 (Cured for 72 hours at 22 °C (non-UV cure)):
- ABS N/mm² :35.7
- Acrylic N/mm² : 14.1
- Aluminum (etched) N/mm² : 17.9
- Neoprene N/mm² : 0.8
- Phenolic N/mm² : 8.2
- Polycarbonate N/mm² :14.1
- Polyethylene N/mm² : 0.4
- Polypropylene N/mm² : 0.3
- PVC N/mm² : 32.7
- Steel (grit blasted) N/mm² : 22.5
Further information can be obtain from local technical department
LOCTITE® 4305 is designed for bonding applications that require very rapid fixturing, fillet cure or surface cure. The UV light cure properties facilitate rapid curing of exposed surface areas thereby minimizing blooming and providing an alternative to solvent borne accelerators. Suitable for use in the assembly of disposable medical devices. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. This product is light sensitive; exposure to daylight, UV light and artificial lighting should be kept to a minimum during storage and handling.
2. For best performance bond surfaces should be clean and free from grease.
3. This product performs best in thin bond gaps (0.05 mm).
4. Excess adhesive can be dissolved with Loctite cleanup solvents, nitromethane or acetone
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.Optimal Storage: 2 °C to 8 °C. Storage below 2 °C or greater than 8 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
- ABS N/mm² :35.7
- Acrylic N/mm² : 14.1
- Aluminum (etched) N/mm² : 17.9
- Neoprene N/mm² : 0.8
- Phenolic N/mm² : 8.2
- Polycarbonate N/mm² :14.1
- Polyethylene N/mm² : 0.4
- Polypropylene N/mm² : 0.3
- PVC N/mm² : 32.7
- Steel (grit blasted) N/mm² : 22.5
Further information can be obtain from local technical department
