LOCTITE MR 5922 - 200ml (fast drying, solvent-based, rubber-modified sealant, black)
No.
IDH.235386
Product description:
LOCTITE MR 5922 is a slow drying, flexible setting paste that changes to a pliable, non-hardening film throughsolvent evaporation. It seals flanges, fittings, connections and flexible assemblies against leakage. It increases the reliability of gasket seals. It is specifically designed to improve the sealing performance of pre-formed gaskets made of cork, metal, plastic, rubber etc.in non-rigid assemblies which may be subject to vibrations and require disassembly on a frequent interval. It may also be used for repair of damaged pre-cut gaskets. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. Remove all previous material from mating surfaces.
2. For best results, clean and dry all surfaces with a residuefree solvent.
3. Remove cap, puncture tube (using self-piercing cap) or cartridge seal and attach extension nozzle (if provided).
4. When used as a gasket dressing, spread product with a spatula to a uniform film on one side of gasket and then position it on the assembly. Coat the second side of gasket and re-assemble. Slower drying formula increases work time.
5. Assembly is operational after 4 hours, full cure is effective after 24 hours.
CLEAN UP:
6. LOCTITE MR 5922 can be removed from metal surfaces with isopropanol. If the sealant has been dried for a long time or at high temperatures, cover the sealant with alcohol and allow to soften overnight.
7. Clean hands with hand cleaners.
Storage:
Store product in the unopened container in a dry location.Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Full technical information can be found in the technical data sheet.
LOCTITE MR 5922 is a slow drying, flexible setting paste that changes to a pliable, non-hardening film throughsolvent evaporation. It seals flanges, fittings, connections and flexible assemblies against leakage. It increases the reliability of gasket seals. It is specifically designed to improve the sealing performance of pre-formed gaskets made of cork, metal, plastic, rubber etc.in non-rigid assemblies which may be subject to vibrations and require disassembly on a frequent interval. It may also be used for repair of damaged pre-cut gaskets. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. Remove all previous material from mating surfaces.
2. For best results, clean and dry all surfaces with a residuefree solvent.
3. Remove cap, puncture tube (using self-piercing cap) or cartridge seal and attach extension nozzle (if provided).
4. When used as a gasket dressing, spread product with a spatula to a uniform film on one side of gasket and then position it on the assembly. Coat the second side of gasket and re-assemble. Slower drying formula increases work time.
5. Assembly is operational after 4 hours, full cure is effective after 24 hours.
CLEAN UP:
6. LOCTITE MR 5922 can be removed from metal surfaces with isopropanol. If the sealant has been dried for a long time or at high temperatures, cover the sealant with alcohol and allow to soften overnight.
7. Clean hands with hand cleaners.
Storage:
Store product in the unopened container in a dry location.Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
- Chemical type: modified resin, fillers and alcohol
- Appearance : black paste
- Smell : alcohol
- Specific gravity : 1.5
- Viscosity : consistency similar to molasses
- Working temperature : from -50 °C to +204 °C
- Resistant to petrol, oils and cooling agents
Full technical information can be found in the technical data sheet.