LOCTITE EA 3472 - 500g (liquid epoxy adhesive with steel filler)
No.
IDH.229175
LOCTITE EA 3472 - 500g (liquid epoxy adhesive with steel filler)
Product description:
LOCTITE EA 3472 is a two-part steel filled epoxy adhesive that is ideal for the repair and recovery of worn and damaged machinery. Typical applications include repairing worn parts such as shafts, housings, keyways, and flanges, as well as broken or damaged parts including castings, pipes, or fabrications. . This product can be used in a variety of jobs including filling cavities, leveling machinery, repairing cast-steel plates, making core molds, applying a sacrificial coating, or sealing leaking pipes. This product is typically used in applications with an operating range of -30 °C to 110 °C. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. Remove dirt, oil, grease, etc. with a suitable cleaner, e.g. high pressure water cleaning system using Loctite® SF 7840 (Loctit Natural Blue cleaner/degreaser).
2. Blast all surfaces to be coated with a sharp edged angular grit to a depth of profile of 75 to 100 microns and a degree of cleanliness of Near White Metal (SIS SA 2½ /SSPC-SP 10).
3. After blasting, metal surfaces should be cleaned with waterless cleaner, e.g. with Loctite SF 7611 (Loctite Pro Strength Parts Cleaner), and be coated before any oxidation or contamination takes place.
4. Metal that has been in contact with salt solutions, e.g. seawater, should be grit blasted, high-pressure water blasted, and left for 24 hours to allow any salts in the metal to sweat to the surface. A test for chloride contamination should be performed. The procedure should be repeated until chloride concentration on the surface is below 40 ppm.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
LOCTITE EA 3472 is a two-part steel filled epoxy adhesive that is ideal for the repair and recovery of worn and damaged machinery. Typical applications include repairing worn parts such as shafts, housings, keyways, and flanges, as well as broken or damaged parts including castings, pipes, or fabrications. . This product can be used in a variety of jobs including filling cavities, leveling machinery, repairing cast-steel plates, making core molds, applying a sacrificial coating, or sealing leaking pipes. This product is typically used in applications with an operating range of -30 °C to 110 °C. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. Remove dirt, oil, grease, etc. with a suitable cleaner, e.g. high pressure water cleaning system using Loctite® SF 7840 (Loctit Natural Blue cleaner/degreaser).
2. Blast all surfaces to be coated with a sharp edged angular grit to a depth of profile of 75 to 100 microns and a degree of cleanliness of Near White Metal (SIS SA 2½ /SSPC-SP 10).
3. After blasting, metal surfaces should be cleaned with waterless cleaner, e.g. with Loctite SF 7611 (Loctite Pro Strength Parts Cleaner), and be coated before any oxidation or contamination takes place.
4. Metal that has been in contact with salt solutions, e.g. seawater, should be grit blasted, high-pressure water blasted, and left for 24 hours to allow any salts in the metal to sweat to the surface. A test for chloride contamination should be performed. The procedure should be repeated until chloride concentration on the surface is below 40 ppm.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
- Typical properties of cured material:
- Hardness (Shore D) : 84
- Tensile strength : 31 N/mm²
- Tensile modulus : 5,85 N/mm²
- Working temperature : -30 °C to +110 °C
- Color : grey
Full technical information can be found in the technical data sheet.
