LOCTITE EA 9514 - 300ml (one-component epoxy adhesive, gray, up to 200 °C)
No.
IDH.2065585
LOCTITE EA 9514 - 300ml (one-component epoxy adhesive, gray, up to 200 °C)
Product description:
LOCTITE® EA 9514 is a toughened, single component heat curing epoxy adhesive. It has high shear and peel strength and excellent impact resistance. LOCTITE® EA 9514 provides high reliability in high operating temperature environments. Its viscosity characteristics ensure large gap filling and sag resistance properties as well as being suitable for a wide variety of substrates. The product can be cured by induction heating or conventional means. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. For best performance surfaces for bonding should be clean, dry and free of grease. You can use LOCTITE SF 7063. For high strength structural bonds, special surface treatments can increase the bond strength and durability.
2. Product can be applied directly from the cartridge by dispensing through the nozzle supplied.
3. It is recommended that this product is not cured in large quantities as excessive heat build-up and uncontrolled exothermal runaway can occur. Curing smaller quantities will minimize the heat build-up.
4. For maximum bond strength apply adhesive evenly to the surface to be bonded. Parts should be assembled immediately after adhesive has been applied.
5. Excess uncured adhesive can be wiped away with organic solvent (e.g. Acetone).
6. Cure adhesive as recommended in section 'Typical Cure Performance'. Some additional fillet may form due to lowering of product viscosity with temperature.
7. Keep the assembled parts from moving during cure. The joint should be allowed to develop full strength before subjecting to any service loads.
8. After use and before adhesive hardens, mixing and application equipment should be cleaned with hot soapy water.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 2 °C to 8 °C. Storage below 2 °C or greater than 8 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
PROPERTIES OF NO-CURED MATERIAL:
PROPERTIES OF CURED MATERIAL:
Shear strength:
Full technical information can be found in the technical data sheet
LOCTITE® EA 9514 is a toughened, single component heat curing epoxy adhesive. It has high shear and peel strength and excellent impact resistance. LOCTITE® EA 9514 provides high reliability in high operating temperature environments. Its viscosity characteristics ensure large gap filling and sag resistance properties as well as being suitable for a wide variety of substrates. The product can be cured by induction heating or conventional means. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. For best performance surfaces for bonding should be clean, dry and free of grease. You can use LOCTITE SF 7063. For high strength structural bonds, special surface treatments can increase the bond strength and durability.
2. Product can be applied directly from the cartridge by dispensing through the nozzle supplied.
3. It is recommended that this product is not cured in large quantities as excessive heat build-up and uncontrolled exothermal runaway can occur. Curing smaller quantities will minimize the heat build-up.
4. For maximum bond strength apply adhesive evenly to the surface to be bonded. Parts should be assembled immediately after adhesive has been applied.
5. Excess uncured adhesive can be wiped away with organic solvent (e.g. Acetone).
6. Cure adhesive as recommended in section 'Typical Cure Performance'. Some additional fillet may form due to lowering of product viscosity with temperature.
7. Keep the assembled parts from moving during cure. The joint should be allowed to develop full strength before subjecting to any service loads.
8. After use and before adhesive hardens, mixing and application equipment should be cleaned with hot soapy water.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 2 °C to 8 °C. Storage below 2 °C or greater than 8 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
PROPERTIES OF NO-CURED MATERIAL:
- Chemical type: epoxy
- Appearance: grey paste
- Specific gravity at 25°C : 1,44
- The yield point at 25°C : 272
- Viscosity " Casson Base" , mPa.s : 42,000
- The maximum gap in the horizontal position : 3 mm
PROPERTIES OF CURED MATERIAL:
Shear strength:
- Steel (shot-blasted) : 45 N/mm²
- Stainless steel : 32 N/mm²
- Zinc coating applied electrolytically : 28 N/mm²
- Aluminum (abraded) : 40 N/mm²
- Aluminum (etched in acidic ferric sulphate) : 40 N/mm²
- Brass : 25 N/mm²
- GRP : 6 N/mm²
- Glass fiber reinforced epoxy : 24 N/mm²
- Galvainzed steel : 20 N/mm²
Full technical information can be found in the technical data sheet
