Try to find the solution
LOCTITE HY 4090 CR - 400g (two-component, general purpose hybrid adhesive, trans
No.
IDH:2002581
Associated products:
- Mixing nozzle Stat. (Mixer for LOCTITE 4090-400ml), (10 pcs / set) (IDH.1573135)
- LOCTITE HY 4090 CR - 50g (hybrid adhesive (cyanoacrylate - epoxy), for general purpose, two-component, white) (IDH.1778011)
- LOCTITE SF 7063 - 400ml (degreasing agent for plastics and metals) spray (IDH.2385316)
- LOCTITE EQ HD 14 400ml 2K (manual dispenser for 2K cartridges) (IDH.2693823)
- LOCTITE EQ HD 14 400ml 2K (pneumatic dispenser for 2K cartridges) (IDH.2693825)
Files to download:
- Karta Techniczna - LOCTITE HY 4090 CR
- Technical Data Sheet - LOCTITE HY 4090 CR
- Technisches Datenblatt - LOCTITE HY 4090 CR
- Karta Charakterystyki (Składnik A) - LOCTITE HY 4090 CR
- Karta charakterystyki (Składnik B) - LOCTITE HY 4090 CR
- Safety Data Sheet (Component A) - LOCTITE HY 4090 CR
- Safety Data Sheet (Component B) - LOCTITE HY 4090 CR
- Sicherheitsdatenblatt (Komponent A) - LOCTITE HY 4090 CR
- Sicherheitsdatenblatt (Komponent B) - LOCTITE HY 4090 CR
Multimedia:
LOCTITE HY 4090 CR - 400g (two-component, general purpose hybrid adhesive, trans
Associated products:
- Mixing nozzle Stat. (Mixer for LOCTITE 4090-400ml), (10 pcs / set) (IDH.1573135)
- LOCTITE HY 4090 CR - 50g (hybrid adhesive (cyanoacrylate - epoxy), for general purpose, two-component, white) (IDH.1778011)
- LOCTITE SF 7063 - 400ml (degreasing agent for plastics and metals) spray (IDH.2385316)
- LOCTITE EQ HD 14 400ml 2K (manual dispenser for 2K cartridges) (IDH.2693823)
- LOCTITE EQ HD 14 400ml 2K (pneumatic dispenser for 2K cartridges) (IDH.2693825)
Product description:
LOCTITE HY 4090 CR is a two component, general purpose adhesive which provides a very fast fixture at room temperature. It is designed to bond a variety of substrates including metals, most plastics and rubbers. LOCTITE HY 4090 CR provides good temperature and moisture resistance which also makes it suitable for applications in high temperature/humidity environments. The thixotropic nature makes it suitable for applications where good gap filling properties on rough and poorly fitting surfaces are required. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. Bond areas should be clean and free from grease. Clean all surfaces with a LOCTITE SF 7063 cleaning solvent and allow todry.
2. To use, Part A and Part B must be blended. Product can be applied directly from dual cartridge by dispensing through the mixer head supplied.
3. Stand dual cartridge upright for 1 minute. Keeping the cartridge in an upright position, insert it into the applicationgun, remove cap and expel a small amount of adhesive to be sure both sides are flowing evenly and freely. Attach the mixing nozzle.
4. Dispense and discard a bead as long and as wide as the mixing nozzle, to ensure sufficient mixing.
5. Apply the mixed adhesive to one of the bond surfaces to be joined. Parts should be assembled immediately after the mixed adhesive has been applied.
6. Bonds should be held fixed or clamped until adhesive has fixtured.
7. Keep assembled parts from moving during cure. The bond should be allowed to develop full strength before subjecting to any service load.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 2°C to 21°C. Storage below 2°C or greater than 21°C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Full technical information can be found in the technical data sheet.
LOCTITE HY 4090 CR is a two component, general purpose adhesive which provides a very fast fixture at room temperature. It is designed to bond a variety of substrates including metals, most plastics and rubbers. LOCTITE HY 4090 CR provides good temperature and moisture resistance which also makes it suitable for applications in high temperature/humidity environments. The thixotropic nature makes it suitable for applications where good gap filling properties on rough and poorly fitting surfaces are required. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. Bond areas should be clean and free from grease. Clean all surfaces with a LOCTITE SF 7063 cleaning solvent and allow todry.
2. To use, Part A and Part B must be blended. Product can be applied directly from dual cartridge by dispensing through the mixer head supplied.
3. Stand dual cartridge upright for 1 minute. Keeping the cartridge in an upright position, insert it into the applicationgun, remove cap and expel a small amount of adhesive to be sure both sides are flowing evenly and freely. Attach the mixing nozzle.
4. Dispense and discard a bead as long and as wide as the mixing nozzle, to ensure sufficient mixing.
5. Apply the mixed adhesive to one of the bond surfaces to be joined. Parts should be assembled immediately after the mixed adhesive has been applied.
6. Bonds should be held fixed or clamped until adhesive has fixtured.
7. Keep assembled parts from moving during cure. The bond should be allowed to develop full strength before subjecting to any service load.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 2°C to 21°C. Storage below 2°C or greater than 21°C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
- Shear strength, ISO 4587, (cured for 168 hours at 22 ° C):
-Steel (grit blasted) N/mm² : 17
-Aluminum N/mm² : 7,6
-Aluminum (etched) N/mm² : 13
-Zinc dichromate N/mm² : 9,1
-Stainless steel N/mm² : 15
-ABS N/mm² : 5,2
-Phenolic N/mm² : 3,2
-Polycarbonate N/mm² : 6,9
-Nitrile N/mm² : 0,7
-Wood (Oak) N/mm² : 4,8
-Epoxy N/mm² : 9,1
-Polyethylene N/mm² : 0,5
-Polypropylene N/mm² : 0,6
Full technical information can be found in the technical data sheet.