TEROSON WX 980 UBC - 1l (anticorrosive agent for vehicle underbodies)
No.
IDH.794867
Product description:
TEROSON WX 980 is a solvent containing, bitumen free anticorrosive agent based on wax, polymers and anticorrosive additives. The product can be precision and exhibits excellent sag resistance. It is fast drying, and even in a thin layerthickness it forms a closed water protecting film. The dry film shows good adhesion and anticorrosive properties.
Application areas:
TEROSON WX 980 is primarily used on wax coated vehicle underbodies and particularly for the secondary treatment of all protective coatings, like those based on PVC, PVC/wax, bitumen/rubber and rubber/resins. In addition the material has proven successful for the following application areas:
- secondary treatment of inaccessible areas, such as corners, edges, seams etc. where rust spots are preferably formed,
- addition of existing coating materials based on PVC, bitumen/rubber, rubber/resins and wax,
- for selective applications and for repair coating of all underbodies after an accident
Further information about the product: biuro@woronko-kleje.pl
Directions for use:
Pretreatment
Surfaces to be treated with TEROSON WX 980 have to be cleaned well and rust must be removed. The areas must be dry and grease, dirt and dust free. In the case of new vehicles, protective wax must be steam-cleaned. If applied to older vehicles, watch out for beginning of rust formation, which has to be removed with a wire brush.
Application
TEROSON WX 980 should have room temperature at time of application. Shake can well, continuing for 1 minute after the ball-bearing becomes audible. Hold can vertically while spraying and apply at a distance of about 20 to 30 cm. Abrasion resistance and corrosion protection increase with the layer thickness. For this reason spraying should be repeated once or twice after a short drying time. In order to avoid bare patches, the material should be spayed in crisscross fashion. After use the can should be held with the value down and the spray should be activated until the jet is cleared and only propellent is emitted.
Storage:
Frost sensitive : no Recommended storage temperature : 10 to 20 °C; (protect from temperatures over 50 °C!) Shelf life 18 months
Parameters:
Colour : anthracite Odour : characteristic odour,like wax, mild Density : approx. 0.97 g/cm³ Layer thickness dry film : 10 to 200 μm ( 2-3 crossing patterns) Drying time : approx. 2 hrs. dust dry Behaviour in the cold no cracking, no flaking : off
Full technical information can be found in technical data sheet
TEROSON WX 980 is a solvent containing, bitumen free anticorrosive agent based on wax, polymers and anticorrosive additives. The product can be precision and exhibits excellent sag resistance. It is fast drying, and even in a thin layerthickness it forms a closed water protecting film. The dry film shows good adhesion and anticorrosive properties.
Application areas:
TEROSON WX 980 is primarily used on wax coated vehicle underbodies and particularly for the secondary treatment of all protective coatings, like those based on PVC, PVC/wax, bitumen/rubber and rubber/resins. In addition the material has proven successful for the following application areas:
- secondary treatment of inaccessible areas, such as corners, edges, seams etc. where rust spots are preferably formed,
- addition of existing coating materials based on PVC, bitumen/rubber, rubber/resins and wax,
- for selective applications and for repair coating of all underbodies after an accident
Further information about the product: biuro@woronko-kleje.pl
Directions for use:
Pretreatment
Surfaces to be treated with TEROSON WX 980 have to be cleaned well and rust must be removed. The areas must be dry and grease, dirt and dust free. In the case of new vehicles, protective wax must be steam-cleaned. If applied to older vehicles, watch out for beginning of rust formation, which has to be removed with a wire brush.
Application
TEROSON WX 980 should have room temperature at time of application. Shake can well, continuing for 1 minute after the ball-bearing becomes audible. Hold can vertically while spraying and apply at a distance of about 20 to 30 cm. Abrasion resistance and corrosion protection increase with the layer thickness. For this reason spraying should be repeated once or twice after a short drying time. In order to avoid bare patches, the material should be spayed in crisscross fashion. After use the can should be held with the value down and the spray should be activated until the jet is cleared and only propellent is emitted.
Storage:
Parameters:
Full technical information can be found in technical data sheet