LOCTITE AA 3295 - 50ml (green acrylic adhesive, up to 120 °C)
No.
IDH.142482
LOCTITE AA 3295 - 50ml (green acrylic adhesive, up to 120 °C)
Product description:
LOCTITE AA 3295 is a two component toughened acrylic adhesive system for high strength structural bonding. The two components are applied premixed from a static mixer which cures rapidly on assembly of the joint. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. For best performance bond surfaces should be clean and free from grease. Use LOCTITE SF 7063.
2. To ensure a fast and reliable cure, product should be applied through a static mixer using appropriate dispensing equipment.
3. Open time in the static mixer is approximately 5 minutes.
4. Avoid cross contamination of the two components of this product.
5. Apply the LOCTITE AA 3295 adhesive immediately and assemble bond (within 5 minutes).
6. Excess adhesive can be wiped away with organic solvent.
7. Bond should be held clamped until adhesive has fixtured.
8. Product should be allowed to develop full strength before subjecting to any service loads (typically 24 to 72 hours after assembly, depending on bond gap, materials and ambient conditions).
Storage:
The product is classified as flammable and must be stored in an appropriate manner in compliance with relevant regulations. Do not store near oxidizing agents or combustible materials. Store product in the unopened container in a dry location. Storage information may also be indicated on the product container labelling.
Optimal Storage: 2 °C to 8 °C. Storage below 2 °C or greater than 8 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Shear strength, ISO 4587 (cured for 48 hours 22 °C):
Full technical information can be found in the technical data sheet.
LOCTITE AA 3295 is a two component toughened acrylic adhesive system for high strength structural bonding. The two components are applied premixed from a static mixer which cures rapidly on assembly of the joint. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. For best performance bond surfaces should be clean and free from grease. Use LOCTITE SF 7063.
2. To ensure a fast and reliable cure, product should be applied through a static mixer using appropriate dispensing equipment.
3. Open time in the static mixer is approximately 5 minutes.
4. Avoid cross contamination of the two components of this product.
5. Apply the LOCTITE AA 3295 adhesive immediately and assemble bond (within 5 minutes).
6. Excess adhesive can be wiped away with organic solvent.
7. Bond should be held clamped until adhesive has fixtured.
8. Product should be allowed to develop full strength before subjecting to any service loads (typically 24 to 72 hours after assembly, depending on bond gap, materials and ambient conditions).
Storage:
The product is classified as flammable and must be stored in an appropriate manner in compliance with relevant regulations. Do not store near oxidizing agents or combustible materials. Store product in the unopened container in a dry location. Storage information may also be indicated on the product container labelling.
Optimal Storage: 2 °C to 8 °C. Storage below 2 °C or greater than 8 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container.
Henkel cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Shear strength, ISO 4587 (cured for 48 hours 22 °C):
- Steel, N/mm² : 24,8
- Aluminum (etched), N/mm² : 17,3
- ABS, N/mm² : 2,1
- PVC, N/mm² : 4,5
- Polycarbonate, N/mm² : 2,8
- Wood, N/mm² : 2,8
- Aluminum (etched), N/mm : 3,5
- Steel: 4,5 hours
- Aluminum: 6 hours
- PVC: 72 hours
- Gap 0,05 mm : 4,5 hours
- Gap 0,5 mm : 24 hours
- Gap 1 mm : 72 hours
Full technical information can be found in the technical data sheet.
