The website uses cookies to provide personalized services at the highest level, including statistical services and to adapt the content to individual preferences of users. Saving cookies can be turned off in your browser settings.
OK
[zamknij]     

LOCTITE FREKOTE 1-STEP - 5 L (mold release agent)

LOCTITE FREKOTE 1-STEP - 5 L (mold release agent) (IDH.380914)

Product description:
Frekote LOCTITE FREKOTE 1-STEP contains a unique polymer designed to release all gel-coated fiberglass reinforced and filled polyester composites. Applications and use of a release agent has never been easier, simply spray on and leave on with no need for polishing . The resulting polymer film retains the original gloss of the mold and is caable of providing multiple releases. Further information about the product: biuro@woronko-kleje.pl

Directions for use:
1. Prior of use of LOCTITE FREKOTE 1-STEP remove dust from the mold by blowing off with a dry and oil free air source.
2. Spray LOCTITE FREKOTE 1-STEP using a high volume low-pressure spray gun. Set the pot pressure at 3 to 6 psi and the air atomization pressure to 35 to 50 psi. Spray using a 1.3 mm diameter spray nozzle.
3. Keep spray head 20 to 25 cm from the mold surface during application. Fine tune air and liquid controls to provide a light, uniform film of LOCTITE FREKOTE 1-STEP that remains wet for approximately 15 to 30 cm behind the pass of the gun head. Setting the air pressure at 35 to 50 psi will reduce the fogging effect of the spray. Slight adjustments of the air and liquid controls on the spray gun will have to be made to insure a light and uniform spray pattern is being produced. In difficult to reach areas, lower air pressure will produce a slightly wetter film that is easier to see and will help to deposit a more uniform film.
4. Systematically apply product to the entire mold surface. Apply each coat perpendicular to the previous coat (up and down wouldbe followed by side to side motion). Lap each stroke over the preceding stroke to insure uniform and complete coverage. Spraying of intricate or deep mold areas can be hard to reach, making it difficult to apply a uniform film in these areas. In these areas it is recommended that initially wiping on and not wiping off a light coat or two of LOCTITE FREKOTE 1-STEP onto the desired areas, followed by the normal application over the entire mold. Wiping on multiple coats requires only solvent evaporation between coats and the subsequent spraying. A dry, clean, lint free cotton cloth should be used for best results.
5. Repeat appliation to give a final coverage of 1 gallon of LOCTITE FREKOTE 1-STEP to 200 square feet of seasoned mold surface, typically 5 coats. A couple of extra coats can be applied in known high wear areas of the mold to provide extra slip. Applyone coat after another. No cure time needed between coats. After spraying final coat, allow to cure for 20 to 30 minutes prior to application of gel coat. Hot summer weather increases plant temperatures causing LOCTITE FREKOTE 1-STEP to evaporate faster than normal. Adjust your spray gun accordingly to insure a proper wet and uniform film is being applied.
6. NOTE: If you are spraying onto a mold large enough that you must walk on the mold, use this simple technique - start at oneend and apply all of the recommended number of coats to one specific section at a time. This can be accomplished because after evaproation of one coat of LOCTITE FREKOTE 1-STEP the next coat can be applied immediately. Repeat this process working your way section by section to the opposite side of the mold. After application is complete, the normal 20 to 30 minutes cure needs to be followed. This technique will eliminate any walking on the mold during the initial application. Some type of foot covering is always recommended when entering a mold to apply.

Storage:
The product is classified as flammable and must be stored in an appropriate manner in compliance with relevant regulations. Do not store near oxidizing agents or combustible materials. Store product in the unopened container in a dry location. Storage information may also be indicated on the product container labelling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.

Parameters:
  • Appearance : clear, colorless
  • Odor: hydrocarbon
  • Cured Thermal Stability : ≤400 °C
  • Application Temperature : 13 to 43 °C
  • High gloss finish
  • Easy application
  • Maximum mold utilization
  • No polishing required
  • Minimal mold build-up

    Full technical information can be found in the technical data sheet
  • Assortment