LOCTITE 5772 - 50ml (anaerobic, yellow, medium strength thread sealant)
No.
IDH.182812
LOCTITE 5772 - 50ml (anaerobic, yellow, medium strength thread sealant)
Product description:
LOCTITE® 5772™ is designed for the locking and sealing of metal threaded pipes and fittings. Particularly suitable for use on stainless steel without the need for surface activation. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. This product has a low halogen and sulphur content and was especially developed for use on sensitive metals, like titanium, used in the nuclear industry. The thixotropic nature of LOCTITE® 5772™ reducesthe migration of liquid product after application to the substrate. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
For Assembly
1. For best results, clean all surfaces (external and internal) with a LOCTITE® SF 7063 cleaning solvent and allow to dry.
2. If the material is an inactive metal or the cure speed is too slow, spray with LOCTITE® SF 7471 or LOCTITE® SF 7649 and allow to dry.
3. Apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also.
4. Using compliant practices, assemble and wrench tighten fittings in accordance with manufacturers recommendations.
5. Properly tightened fittings will seal instantly to moderate pressures. For maximum pressure resistance and solvent resistance allow the product to cure a minimum of 24 hours.
For Disassembly
1. Remove with standard hand tools.
2. Where hand tools do not work because of excessive engagement length or large diameters (over 1"), apply localized heat to approximately 250 °C. Disassemble while hot.
For Cleanup
1. Cured product can be removed with a combination of soaking in a LOCTITE® SF 7200 solvent and mechanical abrasion such as a wire brush.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Specific Gravity at 25 °C : 1.09 Breakaway Torque, ISO 10964 (Cured for 1 hour at 22 °C):
- M10 stainless steel nuts and bolts, N·m : 1.0 Prevail Torque, ISO 10964 (Cured for 1 hour at 22 °C):
- M10 stainless steel nuts and bolts, N·m : 0.5 Breakaway Torque, ISO 10964 (Cured for 24 hours at 22 °C):
- M10 black oxide steel nuts and bolts, N·m : 17
- M10 stainless steel nuts and bolts, N·m : 6.4 Prevail Torque, ISO 10964 (Cured for 24 hours at 22 °C):
- M10 black oxide steel nuts and bolts, N·m : 6
- M10 stainless steel nuts and bolts, N·m : 3.4 Compressive Shear Strength, ISO 10123 (Cured for 24 hours at 22 °C):
- Steel pins and collars, N/mm² : ≥1.2
Full technical information can be found in the technical data sheet
LOCTITE® 5772™ is designed for the locking and sealing of metal threaded pipes and fittings. Particularly suitable for use on stainless steel without the need for surface activation. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. This product has a low halogen and sulphur content and was especially developed for use on sensitive metals, like titanium, used in the nuclear industry. The thixotropic nature of LOCTITE® 5772™ reducesthe migration of liquid product after application to the substrate. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
For Assembly
1. For best results, clean all surfaces (external and internal) with a LOCTITE® SF 7063 cleaning solvent and allow to dry.
2. If the material is an inactive metal or the cure speed is too slow, spray with LOCTITE® SF 7471 or LOCTITE® SF 7649 and allow to dry.
3. Apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also.
4. Using compliant practices, assemble and wrench tighten fittings in accordance with manufacturers recommendations.
5. Properly tightened fittings will seal instantly to moderate pressures. For maximum pressure resistance and solvent resistance allow the product to cure a minimum of 24 hours.
For Disassembly
1. Remove with standard hand tools.
2. Where hand tools do not work because of excessive engagement length or large diameters (over 1"), apply localized heat to approximately 250 °C. Disassemble while hot.
For Cleanup
1. Cured product can be removed with a combination of soaking in a LOCTITE® SF 7200 solvent and mechanical abrasion such as a wire brush.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
- M10 stainless steel nuts and bolts, N·m : 1.0
- M10 stainless steel nuts and bolts, N·m : 0.5
- M10 black oxide steel nuts and bolts, N·m : 17
- M10 stainless steel nuts and bolts, N·m : 6.4
- M10 black oxide steel nuts and bolts, N·m : 6
- M10 stainless steel nuts and bolts, N·m : 3.4
- Steel pins and collars, N/mm² : ≥1.2
Full technical information can be found in the technical data sheet
