LOCTITE EA 3425 - 200ml (epoxy adhesive)
No.
IDH.2063050
Associated products:
- Mixing nozzle Stat Mixer 7.5-24 1:1 and 2:1, Type No. 984570 (200/400ml cat.) (IDH.1487439A)
- LOCTITE Universal Fixmaster Dispenser 200ml, 400ml, 490ml, manual gun (IDH.1372751)
- LOCTITE SF 7063 - 400ml (degreasing agent for plastics and metals) spray (IDH.2385316)
- LOCTITE EQ HD 14 200ml 2K (pneumatic dispenser for 2K cartridges) (IDH.2693824)
- LOCTITE EA 3425 - 50ml (epoxy adhesive) (IDH.2063045)
- LOCTITE EQ HD 14 200ml 2K (manual dispenser for 2K cartridges) (IDH.2693822)
LOCTITE EA 3425 - 200ml (epoxy adhesive)
Associated products:
- Mixing nozzle Stat Mixer 7.5-24 1:1 and 2:1, Type No. 984570 (200/400ml cat.) (IDH.1487439A)
- LOCTITE Universal Fixmaster Dispenser 200ml, 400ml, 490ml, manual gun (IDH.1372751)
- LOCTITE SF 7063 - 400ml (degreasing agent for plastics and metals) spray (IDH.2385316)
- LOCTITE EQ HD 14 200ml 2K (pneumatic dispenser for 2K cartridges) (IDH.2693824)
- LOCTITE EA 3425 - 50ml (epoxy adhesive) (IDH.2063045)
- LOCTITE EQ HD 14 200ml 2K (manual dispenser for 2K cartridges) (IDH.2693822)
Product description:
LOCTITE EA 3425 is a two component, high viscosity, thixotropic epoxy adhesive which cures at room temperature after mixing. It is a general purpose, non sag adhesive which develops high strength on a wide range of substrates. The thixotropic properties enable this adhesive system to bond rough vertical surfaces made from metal, ceramic, rigid plastics or wood through gaps of up to 3 mm. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. For best performance surfaces for bonding should be clean, dry and free of grease. You can use LOCTITE SF 7063 For high strength structural bonds, special surface treatments can increase the bond strength and durability.
2. To use, resin and hardener must be blended. Product can be applied directly from dual cartridges by dispensing through the mixer head supplied. Discard the first 3 to 5 cm of bead dispensed. Using bulk containers, mixt horoughly by weight or volume in the proportions specified in the Product Description Matrix. For handmixing, weigh or measure out the desired amount of resin and hardener and mix thoroughly. Mix approximately 15 seconds after uniform color is obtained.
3. It is recommended that this product is not mixed and cured in bulk quantities of greater than 4 kg as excessive heat build-up can occur. Mixing smaller quantities will minimize the heat build-up.
4. Apply the adhesive as quickly as possible after mixing to one surface to be joined. For maximum bond strength apply adhesive evenly to both surfaces. Parts should be assembled immediately after mixed adhesive has been applied.
5. For working life please see section 'Typical Properties of Uncured Material'. Higher temperatures and larger quantities will shorten this working time.
6. Keep the assembled parts from moving during cure. The joint should be allowed to develop full strength before subjecting to any service loads.
7. Excess uncured adhesive can be wiped away with organic solvent (e.g. Acetone).
8. After use and before adhesive hardens, mixing and application equipment should be cleaned with hot soapy water.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Full technical information can be found in the technical data sheet.
LOCTITE EA 3425 is a two component, high viscosity, thixotropic epoxy adhesive which cures at room temperature after mixing. It is a general purpose, non sag adhesive which develops high strength on a wide range of substrates. The thixotropic properties enable this adhesive system to bond rough vertical surfaces made from metal, ceramic, rigid plastics or wood through gaps of up to 3 mm. Further information about the product: biuro@woronko-kleje.pl
Steps to achieve the best adhesive results:
1. For best performance surfaces for bonding should be clean, dry and free of grease. You can use LOCTITE SF 7063 For high strength structural bonds, special surface treatments can increase the bond strength and durability.
2. To use, resin and hardener must be blended. Product can be applied directly from dual cartridges by dispensing through the mixer head supplied. Discard the first 3 to 5 cm of bead dispensed. Using bulk containers, mixt horoughly by weight or volume in the proportions specified in the Product Description Matrix. For handmixing, weigh or measure out the desired amount of resin and hardener and mix thoroughly. Mix approximately 15 seconds after uniform color is obtained.
3. It is recommended that this product is not mixed and cured in bulk quantities of greater than 4 kg as excessive heat build-up can occur. Mixing smaller quantities will minimize the heat build-up.
4. Apply the adhesive as quickly as possible after mixing to one surface to be joined. For maximum bond strength apply adhesive evenly to both surfaces. Parts should be assembled immediately after mixed adhesive has been applied.
5. For working life please see section 'Typical Properties of Uncured Material'. Higher temperatures and larger quantities will shorten this working time.
6. Keep the assembled parts from moving during cure. The joint should be allowed to develop full strength before subjecting to any service loads.
7. Excess uncured adhesive can be wiped away with organic solvent (e.g. Acetone).
8. After use and before adhesive hardens, mixing and application equipment should be cleaned with hot soapy water.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
- The shelf life of the mixed adhesive:
-Temperature 25 ºC : 120 minutes
- Selected typical properties of hardened material:
- Hardness, (Shore D) : 70 to 80
- Elongation, % : 2,9
- Tensile modulus : 1353 N/mm²
- Working temperature : -20 ºC to +120 ºC
- Hand strength (0,1 N/mm²) : 240 minutes
- High strength : after 24 godz.
- Color : yellow-white paste
- Shear strength after 7 days ( temperature 23 ºC ):
- Stel shot-blasted : 28 N/mm²
- Stainless steel : 11,5 N/mm²
- Polished aluminum : 10 N/mm²
- Aluminum etched : 20 N/mm²
- Zinc coating (applied by immersion): 13,7 N/mm²
- Zinc coating (applied electrolytically) : 14 N/mm²
- Brass : 13 N/mm²
- GRP : 0,8 N/mm²
- Phenolic material : 3 N/mm²
- ABS : 0,5 N/mm²
- Polycarbonate : 3 N/mm²
- Wood (hard) : 12 N/mm²
- Wood (soft) : 9,5 N/mm²
Full technical information can be found in the technical data sheet.