LOCTITE SI 5607 - 400ml (Silicone adhesive)
No.
IDH.2056425
Product description:
LOCTITE® SI 5607™ is a two-part, neutral curing silicone with medium cure speed. Typical applications include bonding and sealing in the appliance market and general applications where a long working life after dispensing is required. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. For high strength structural bonds, remove surface contaminants such as paint, oxide films, oils, dust, mold release agents and all other surface contaminants. You can use LOCTITE SF 7063.
2. Use gloves to minimize skin contact. DO NOT use solvents for cleaning hands.
3. Dual Cartridges: To begin using a new cartridge, remove cartridge cap and dispense a small amount of adhesive, making sure both parts A&B are extruding. Attach nozzle and dispense approximately 25 to 50mm, before applying onto part to be bonded. Partially usedcartridges can be stored with the mixing nozzle attached. To reuse, remove and discard old nozzle, attach the new nozzle, dispense approximately 25 to 50mm, before applying onto part to be bonded. Bulk Containers: Normally material is dispensedthrough volumetric metered mixing equipment, attached to static mix nozzles.
4. Application to the substrates should be made as soon as possible. Larger quantities and/or higher temperatures will reduce the working time.
5. Keep assembled parts from moving during cure. The bond should be allowed to develop full strength before subjecting to any service load.
6. Excess material can be easily wiped away with non-polar solvents.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:Hardness, Shore, ISO 868, Shore A: 30 to 50 Tensile strength, ISO 527-3 N / mm²: ≥1.0 Elongation at break, ISO 527-3,%: ≥80 Tensile strength, ISO 527-3 N / mm²: 2 Modulus of elasticity, ISO 527-3 N / mm²: 0.6
Further information can be found in technical data sheet
LOCTITE® SI 5607™ is a two-part, neutral curing silicone with medium cure speed. Typical applications include bonding and sealing in the appliance market and general applications where a long working life after dispensing is required. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. For high strength structural bonds, remove surface contaminants such as paint, oxide films, oils, dust, mold release agents and all other surface contaminants. You can use LOCTITE SF 7063.
2. Use gloves to minimize skin contact. DO NOT use solvents for cleaning hands.
3. Dual Cartridges: To begin using a new cartridge, remove cartridge cap and dispense a small amount of adhesive, making sure both parts A&B are extruding. Attach nozzle and dispense approximately 25 to 50mm, before applying onto part to be bonded. Partially usedcartridges can be stored with the mixing nozzle attached. To reuse, remove and discard old nozzle, attach the new nozzle, dispense approximately 25 to 50mm, before applying onto part to be bonded. Bulk Containers: Normally material is dispensedthrough volumetric metered mixing equipment, attached to static mix nozzles.
4. Application to the substrates should be made as soon as possible. Larger quantities and/or higher temperatures will reduce the working time.
5. Keep assembled parts from moving during cure. The bond should be allowed to develop full strength before subjecting to any service load.
6. Excess material can be easily wiped away with non-polar solvents.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Further information can be found in technical data sheet