LOCTITE FREKOTE WOLO - 1L (release agent)
No.
IDH.381139
Associated products:
Product description:
LOCTITE Frekote WOLO is a unique, low VOC polymer release agent that cures quickly and provides multiple release of all polyester resins. Applications and use of a release agent has never been easier, simply wipe on and leave on to produce a high gloss finish with no need to polish. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. Apply LOCTITE Frekote WOLO with a clean, lint free, cotton wiping cloth. Wet the cloth with LOCTITE Frekote WOLO until it is damp but not dripping.
2. Wipe a smooth, wet film over the entire mold surface. For larger molds, apply LOCTITE Frekote WOLO to the surface one section at a time starting at one end and working towards the other. Continue to work the material into the mold by lightly wiping the wet film (10-30 seconds) until a thin and uniform coating is obtained, and then allow the product to evaporate.
3. Allow a minimum of 5 minutes before applying next coat. Apply a minimum of four coats in this manner. Dampen cloth lightly as needed.
4. Allow the final coat to cure for 15 minutes at 20°C.
5. NOTE: If the cloth dries out during your coating process, use a fresh clean cloth to apply the next coat. This prevents resin accumulation on the cloth from being deposited on the mold surface. If streaking occurs, replace the cloth with a clean dry one and/or make sure that the cloth is just damp and not soaking wet. Avoid over-application, as this will cause streaking on the tooling surface. Streaks or wipe lines can be removed easily by wiping the mold surface lightly with a dry cloth. Product is moisture sensitive, keep container tightly closed when not in use.
6. NOTE: For maximum number of releases, apply a touch up coat after the first 2-3 parts are released as a break in period after the initial application. On deep or high wear areas, apply an extra 1-2 coats of LOCTITE Frekote WOLO. This will help increase the slip even further in these high drag areas.
Storage:
The product is classified as flammable and must be stored in an appropriate manner in compliance with relevant regulations. Do not store near oxidizing agents or combustible materials. Store product in the unopened container in a dry location. Storage information may also be indicated on the product container labelling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Appearance : clear, colorless Chemical type : solvent based polymer Odor : hydrocarbon Application temperature : 13 to 41 °C High gloss finish Easy application Fast curing Multiple releases Minimal mold build-up
Full technical information can be found in the technical data sheet
LOCTITE Frekote WOLO is a unique, low VOC polymer release agent that cures quickly and provides multiple release of all polyester resins. Applications and use of a release agent has never been easier, simply wipe on and leave on to produce a high gloss finish with no need to polish. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. Apply LOCTITE Frekote WOLO with a clean, lint free, cotton wiping cloth. Wet the cloth with LOCTITE Frekote WOLO until it is damp but not dripping.
2. Wipe a smooth, wet film over the entire mold surface. For larger molds, apply LOCTITE Frekote WOLO to the surface one section at a time starting at one end and working towards the other. Continue to work the material into the mold by lightly wiping the wet film (10-30 seconds) until a thin and uniform coating is obtained, and then allow the product to evaporate.
3. Allow a minimum of 5 minutes before applying next coat. Apply a minimum of four coats in this manner. Dampen cloth lightly as needed.
4. Allow the final coat to cure for 15 minutes at 20°C.
5. NOTE: If the cloth dries out during your coating process, use a fresh clean cloth to apply the next coat. This prevents resin accumulation on the cloth from being deposited on the mold surface. If streaking occurs, replace the cloth with a clean dry one and/or make sure that the cloth is just damp and not soaking wet. Avoid over-application, as this will cause streaking on the tooling surface. Streaks or wipe lines can be removed easily by wiping the mold surface lightly with a dry cloth. Product is moisture sensitive, keep container tightly closed when not in use.
6. NOTE: For maximum number of releases, apply a touch up coat after the first 2-3 parts are released as a break in period after the initial application. On deep or high wear areas, apply an extra 1-2 coats of LOCTITE Frekote WOLO. This will help increase the slip even further in these high drag areas.
Storage:
The product is classified as flammable and must be stored in an appropriate manner in compliance with relevant regulations. Do not store near oxidizing agents or combustible materials. Store product in the unopened container in a dry location. Storage information may also be indicated on the product container labelling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Full technical information can be found in the technical data sheet