LOCTITE SF 7100 - 400ml (leak detector, aqueous based)
No.
IDH.250000
LOCTITE SF 7100 - 400ml (leak detector, aqueous based)
Product description:
LOCTITE SF 7100 is a product in an easy to use aerosol, that allows for detection of suspected leaks. This product starts producing bubbles at areas where a leak is present. It is non-toxic and non-flammable. LOCTITE SF 7100 is designed for tracing leaks in all pressurized gas systems, as well as compressed air, helium, nitrogen etc. The product can be used for common pipings made from iron, copper and plastic. This product is typically used in applications with an operating range of 10 °C to 50 °C. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. Shake can thoroughly. Spray at a distance of about 15 to 20 cm onto the suspect area.
2. A leak will be clearly visible, as the product will start foaming at the leaking area. The product will continue to foam, allowing for a thorough search without rushing.
3. If the leak is not in the repair area, the leak search has to be extended to entire system. The leak will be in the area where the product starts foaming.
4. After the leak has been detected, wipe off excess product and perform appropriate maintenance.
5. To ensure the maintenance performed was successful, apply LOCTITE SF 7100 again to the respective area.
6. On hydraulic components leaks are normally clearly visible without any product. However, for a leak check after repair or on new components, prior to component installation, LOCTITE SF 7100 can be used for detecting potential leaks. For this purpose, fill the component with pressurised air and apply product to suspect area.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Full technical information can be found in the technical data sheet.
LOCTITE SF 7100 is a product in an easy to use aerosol, that allows for detection of suspected leaks. This product starts producing bubbles at areas where a leak is present. It is non-toxic and non-flammable. LOCTITE SF 7100 is designed for tracing leaks in all pressurized gas systems, as well as compressed air, helium, nitrogen etc. The product can be used for common pipings made from iron, copper and plastic. This product is typically used in applications with an operating range of 10 °C to 50 °C. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. Shake can thoroughly. Spray at a distance of about 15 to 20 cm onto the suspect area.
2. A leak will be clearly visible, as the product will start foaming at the leaking area. The product will continue to foam, allowing for a thorough search without rushing.
3. If the leak is not in the repair area, the leak search has to be extended to entire system. The leak will be in the area where the product starts foaming.
4. After the leak has been detected, wipe off excess product and perform appropriate maintenance.
5. To ensure the maintenance performed was successful, apply LOCTITE SF 7100 again to the respective area.
6. On hydraulic components leaks are normally clearly visible without any product. However, for a leak check after repair or on new components, prior to component installation, LOCTITE SF 7100 can be used for detecting potential leaks. For this purpose, fill the component with pressurised air and apply product to suspect area.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
- Chemical type: synthetic sulfonate with anionic surfactants, anti-corrosive additives
- Color: pale yellow
- Odor: odorless
- Specific gravity, g/ml: 1.02
- Value pH: 7.2
- Reg. in water: completely soluble
- Propellant: CO2
Full technical information can be found in the technical data sheet.
