TEROSON Bond 15 - 310ml (Glass adhesive, super fast)
No.
IDH.2671464
Product description:
TEROSON® BOND 15 is a one-component polyurethane adhesive. Both skin formation and curing times are dependent on humidity and temperature. The cure time may vary depending on the joint depth. By increasing the temperature and humidity, the reaction time can be reduced. Low temperature as well as low moisture slows down the process. It has an excellent adhesion to glass, glass with the ceramic coating, encapsulation and to painted surfaces in connection with primer / activator. Typical applications include the bonding of front, rear and side screens to the body of passenger-, utility-, special- and rail vehicles. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
Priming
1. Before opening the TEROSON® BOND ALL-IN-ONEPRIMER bottle, shake well (at least 1 minute).
2. Apply primer with wool dauber in one pass on the bond line (allow to flash off for 2 minutes).
3. Within the first 2 hours after cutting back the old adhesive bead in the body frame, it does not need to be primed. But if the replacement takes longer than 2 hours, the old cut bead needs to be activated with TEROSON® BOND ALL-IN-ONE PRIMER. NOTE: Provided that it is not contaminated with dust or grease, the old cut adhesive bead is the best adhesive surface for the TEROSON® BOND 15 adhesive.
4. If windows are bonded which have been pre-coated with a primer or PU–based adhesive/sealant by the glass supplier, TEROSON® BOND ALL-IN-ONE-PRIMER is also suitable to ensure the correct adherence of TEROSON® BOND 15 to the pre-coating.
5. Using a wool dauber, a thin layer of TEROSON® BOND ALL-IN-ONE-PRIMER is applied to the pre-coating. Allow to flash off for 2 minutes. Subsequently, TEROSON® BOND 15 is applied as usual, but taking into consideration the layer thickness of the pre-coating.
Application
1. Prior to its use, the cartridge of TEROSON® BOND 15 must be warmed to above 60°C. There are 2 heating devices which could be used. In the TEROSON® ET CR HEATINGBOX 2PC minimum 15 minutes or in the TEROSON® ET CR FC HEATINGBOX 6PC device minimum 30 minutes.
2. The windscreen adhesive TEROSON® BOND 15 is processed hot from the cartridge or foil pack using commercial equipment such as hand, battery driven or air-pressure dispensers with a piston rod.
3. The Safe Drive-Away Time of TEROSON® BOND 15 must be respected.
Storage:
Store product in the unopened container in a dry location. Storage information may also be indicated on the product container labelling. Optimal Storage: 15 to 25 °C. Storage below 5 °C or greater than 25 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:Chemical type : polyurethane Appearance (uncured) : black Components : one-component – requires no mixing Viscosity : paste Cure : humidity Application Windscreen Adhesive Environmental temperature at application : 5 to 45 °C Material application temperature : 60 to 70 °C In service temperature : -40 to 90 °C Short exposure (up to 1h) 120 °C Safe Drive-Away time with airbag:
-Crash Norm FMVSS 212/208 Crash Test 48 km/h, 100% head-on : 15 minutes
Full technical information can be found in technical data sheet
TEROSON® BOND 15 is a one-component polyurethane adhesive. Both skin formation and curing times are dependent on humidity and temperature. The cure time may vary depending on the joint depth. By increasing the temperature and humidity, the reaction time can be reduced. Low temperature as well as low moisture slows down the process. It has an excellent adhesion to glass, glass with the ceramic coating, encapsulation and to painted surfaces in connection with primer / activator. Typical applications include the bonding of front, rear and side screens to the body of passenger-, utility-, special- and rail vehicles. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
Priming
1. Before opening the TEROSON® BOND ALL-IN-ONEPRIMER bottle, shake well (at least 1 minute).
2. Apply primer with wool dauber in one pass on the bond line (allow to flash off for 2 minutes).
3. Within the first 2 hours after cutting back the old adhesive bead in the body frame, it does not need to be primed. But if the replacement takes longer than 2 hours, the old cut bead needs to be activated with TEROSON® BOND ALL-IN-ONE PRIMER. NOTE: Provided that it is not contaminated with dust or grease, the old cut adhesive bead is the best adhesive surface for the TEROSON® BOND 15 adhesive.
4. If windows are bonded which have been pre-coated with a primer or PU–based adhesive/sealant by the glass supplier, TEROSON® BOND ALL-IN-ONE-PRIMER is also suitable to ensure the correct adherence of TEROSON® BOND 15 to the pre-coating.
5. Using a wool dauber, a thin layer of TEROSON® BOND ALL-IN-ONE-PRIMER is applied to the pre-coating. Allow to flash off for 2 minutes. Subsequently, TEROSON® BOND 15 is applied as usual, but taking into consideration the layer thickness of the pre-coating.
Application
1. Prior to its use, the cartridge of TEROSON® BOND 15 must be warmed to above 60°C. There are 2 heating devices which could be used. In the TEROSON® ET CR HEATINGBOX 2PC minimum 15 minutes or in the TEROSON® ET CR FC HEATINGBOX 6PC device minimum 30 minutes.
2. The windscreen adhesive TEROSON® BOND 15 is processed hot from the cartridge or foil pack using commercial equipment such as hand, battery driven or air-pressure dispensers with a piston rod.
3. The Safe Drive-Away Time of TEROSON® BOND 15 must be respected.
Storage:
Store product in the unopened container in a dry location. Storage information may also be indicated on the product container labelling. Optimal Storage: 15 to 25 °C. Storage below 5 °C or greater than 25 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
-Crash Norm FMVSS 212/208 Crash Test 48 km/h, 100% head-on : 15 minutes
Full technical information can be found in technical data sheet